- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Surestore 418 Autoloader-->"Not Ready-Door Open" E...
StoreEver Tape Storage
1753758
Members
4622
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-18-2002 12:12 PM
03-18-2002 12:12 PM
Surestore 418 Autoloader-->"Not Ready-Door Open" Error
I had a bent door, swapped one of a bad unit, and I am getting this "Not Ready-Door Open" error. Door is closed, and the only thing which looks like a switch seems to be working. The 2 black plastic levers are recessed into holes in the top, and plastic protrusions on the door look like they enter the holes and close the levers. Cannot see any other switch type devices. Does anyone know exactly what actuates the door opened error ???
Thank you,
John
Thank you,
John
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-19-2002 03:36 PM
03-19-2002 03:36 PM
Re: Surestore 418 Autoloader-->"Not Ready-Door Open" Error
There are three holes at the top of the door. The two large rectangular holes on the side are for guides only. The narrow hole is the middle is where the door open sensor is located. The sensor occupies the top 1/3 of that hole. One the door there is a small peg that pushes the sensor to indicate the door is closed. That peg should be the same height as the guide blocks on both sides and positioned slightly above them. If it is broken or bent this error will occur. You can test the sensor by using a foam tip cleaning swab and pushing it into the top 1/3 of the hole while power is on and see if the library detects it and begins the initializing sequence. If it does then the problem is the pusher on the door. If the library still reports door open then the sensor may be damaged. If you can't get the library to power up the sensor will have to be tested with a multi-meter. If you know how that is really easy when you take the cover off. If you don't already know how it probably can't be explained here.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP