- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: TL891 & BE8.5
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-25-2001 04:00 PM
тАО02-25-2001 04:00 PM
TL891 & BE8.5
I have a TL891 (twogether with a DataUnit 128670-B21 and a ExpansionUnit 120877-B21) connected to a ML380. OS=WniNT4.0 SP6. BackupExec 8.5
ID's: TL891=0; Exp.Unit=1; DLT0=4; DLT1=5
I'm able to backup data to the library, but:
- BE uses only DLT0 (DLT 1 is working if I define it in a sep. Backup-Job) Should I be able to backup simultanious to both DLT's with ONE Backup-Job?
- BE uses only the 10Slot Magazin in the TL891. the 2 other 16Slot Magazins are not used.
- BE does create two entries:
1. TL891 with 2DLT's & 10 Tapes
2. 32 Tapes
As far as I know it should only be one entry... but how can I tell this to BE????
I did this configuration first with a Adaptec 2944UW, connecting all devices to the external Port (Backup was 230MB/min)
Now I connected it to a Modular Data Router via fibre (backup is 250MB/min.)
Should I get a higher backup-rate?
thanks for your help
Flex
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-25-2001 04:00 PM
тАО02-25-2001 04:00 PM
Re: TL891 & BE8.5
*********************** IMPORTANT: All MiniLibrary Base Units are shipped as standalone systems. Before powering up the Expansion Unit in a MiniLibrary system after adding Base Units, you must re-configure each new Base Unit in the system as a slave. The Expansion Unit is the master for the entire library.
View the Base Unit's front panel.
Go to the Alternate Configuration menu.
Change the fourth line to 'Slave'.
Save the new selection. Repeat for each Base Unit.
Change SCSI IDs, if necessary at this point. Refer to the product documentation for specific instructions. The SCSI IDs must be unique. So if there are drives daisy-chained together, you might need to change the IDs. Compaq strongly recommends limiting how many drives are daisy-chained together.
Cycle the power when done.
******************************** But... It did'nt work... after I've done what the above text tells me, the TL891 will perform a Firmwareupdate... During this Update the ExpansionUnit came with a errormessage and now both (TL891 and DataUnit) are waiting to "synch with Master or Host".
s**t
I've downloaded the Firmware Upgrade for the TL891 (170678-001) but it tells me that there is either no Firmware on the disk or no DLT-Library. I tried it via fibre (with modular Data Router) and direkt with a Adaptec2944UW. ---- Both the same error...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2001 04:00 PM
тАО02-26-2001 04:00 PM
Re: TL891 & BE8.5
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2001 04:00 PM
тАО04-02-2001 04:00 PM
Re: TL891 & BE8.5
Have you found any solution? I have the same problem here, but don't want to upgrade to w2k.
Gr,
Steven
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2001 04:00 PM
тАО04-02-2001 04:00 PM
Re: TL891 & BE8.5
We don't have a problem, on NT4 we use Veritas BackupExec, on W2K we installed the minilibrary-driver.
Kind Regards,
Anton Rutten
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2001 04:00 PM
тАО04-04-2001 04:00 PM