- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Tape status poor after backup
StoreEver Tape Storage
1753798
Members
7985
Online
108805
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-04-2008 07:49 PM
тАО02-04-2008 07:49 PM
I have tape library HP MSL 2024, DP 6.0, Windows 2003 r2, LSI Adapter Ultra320 SCSI.
After backup in drive 1 status tape is poor and backup very slow. After verify status good.
In drive 2 all normal.
Testing in L&TT show this warning:
The current SCSI configuration is likely to be limiting the performance of the drive.
Please check that your HBA is the correct type for the drive and that the cabling is good.
The SCSI configuration referenced is the one for which device analysis was run and/or the support ticket was pulled.
If this is not via your backup server then you may not have an issue.
Current SCSI configuration\: narrow Recommended\: wide
Current SCSI transfer rate limited to\: 20 MB/sec. Recommended\: 160 MB/sec. or better.
Thanks for all ideas
After backup in drive 1 status tape is poor and backup very slow. After verify status good.
In drive 2 all normal.
Testing in L&TT show this warning:
The current SCSI configuration is likely to be limiting the performance of the drive.
Please check that your HBA is the correct type for the drive and that the cabling is good.
The SCSI configuration referenced is the one for which device analysis was run and/or the support ticket was pulled.
If this is not via your backup server then you may not have an issue.
Current SCSI configuration\: narrow Recommended\: wide
Current SCSI transfer rate limited to\: 20 MB/sec. Recommended\: 160 MB/sec. or better.
Thanks for all ideas
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-05-2008 10:54 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 02:45 AM
тАО02-06-2008 02:45 AM
Re: Tape status poor after backup
Thaks Bill Costigan.
After replacement cable and terminator testing in L&TT show that all normal
After replacement cable and terminator testing in L&TT show that all normal
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP