- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- colorado 14 GB int.
StoreEver Tape Storage
1753882
Members
7588
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-04-2003 01:19 AM
тАО02-04-2003 01:19 AM
colorado 14 GB int.
I cannot get this tape drive to work with WIN NT.
Tape drive is configured as Master on Secondary IDE - no Slave present. Every time i try to start a backup i get the message unable to find to find the drive, check cable. The driver is the newest one and everything i checked is okay. windows does recognise the tape drive in Hardware settings and says it is working OK. What else can i do?
thanxs norbert
Tape drive is configured as Master on Secondary IDE - no Slave present. Every time i try to start a backup i get the message unable to find to find the drive, check cable. The driver is the newest one and everything i checked is okay. windows does recognise the tape drive in Hardware settings and says it is working OK. What else can i do?
thanxs norbert
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-04-2003 08:34 AM
тАО02-04-2003 08:34 AM
Re: colorado 14 GB int.
Need to verify the tape drive is being seen by the hardware.
Does the tape drive banner during POST?
Do any other IDE devices work if connected to the secondary IDE?
When was this tape drive last working ok? In what configuration?
Does the tape drive banner during POST?
Do any other IDE devices work if connected to the secondary IDE?
When was this tape drive last working ok? In what configuration?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-04-2003 10:48 PM
тАО02-04-2003 10:48 PM
Re: colorado 14 GB int.
Yes the tape drive is seen by the hardware and i checked the tape drive on an other secondary IDE the same result.The last time we used is one month away.
norbert
norbert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-08-2003 04:21 AM
тАО02-08-2003 04:21 AM
Re: colorado 14 GB int.
hallo Norbert,
witch software do you use?
and witch are teh settings in the bios?
The drive need to set on Pio-mode O and the UDMA has to be disabled!!
also the chipset on the board can be faulty.This tape with the VIA,ALI and SIS chipset has problems!
the correct driver for this tape is
Under NT 4.0 ? QIC157.sys( found on the NT CD!)
with Colorado-Backup = HPQIC157.sys) embedded in the program!
witch software do you use?
and witch are teh settings in the bios?
The drive need to set on Pio-mode O and the UDMA has to be disabled!!
also the chipset on the board can be faulty.This tape with the VIA,ALI and SIS chipset has problems!
the correct driver for this tape is
Under NT 4.0 ? QIC157.sys( found on the NT CD!)
with Colorado-Backup = HPQIC157.sys) embedded in the program!
Carmen Juergens
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP