- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- disk drive for hp9000-k460 a3353a
StoreEver Tape Storage
1752806
Members
5903
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-30-2004 06:21 AM
06-30-2004 06:21 AM
disk drive for hp9000-k460 a3353a
Our engineer onsite is going to install an editional 4gb scsi disk drive that we have purchased so we can disperse some of our files to it.
My question is: is there a special configuration that needs to be done to the drive in order for the server to recognize it? Pins? Jumpers?
ETC?
Thanks,
Byron
My question is: is there a special configuration that needs to be done to the drive in order for the server to recognize it? Pins? Jumpers?
ETC?
Thanks,
Byron
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-01-2004 08:04 PM
07-01-2004 08:04 PM
Re: disk drive for hp9000-k460 a3353a
Hi Byron,
There are several different flavours of A3353A, in the Disc Upgrade Manual it lists 2 different drives and the only links you really need to set are the address links. The drives are usually numbered in the cage from the top down 6,5,4,3 so you will need to link for the address you require. If you have a ST15150WD then the address links are pins 1-4 on connector J5 which is nearest to the DC connector. The links are the same on the ST34371WD drive.
hope this helps
malvin
There are several different flavours of A3353A, in the Disc Upgrade Manual it lists 2 different drives and the only links you really need to set are the address links. The drives are usually numbered in the cage from the top down 6,5,4,3 so you will need to link for the address you require. If you have a ST15150WD then the address links are pins 1-4 on connector J5 which is nearest to the DC connector. The links are the same on the ST34371WD drive.
hope this helps
malvin
Not me Chief, I'm Radar
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP