- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: msl6060 master, slave scsi cabling
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2006 11:32 PM
тАО06-29-2006 11:32 PM
msl6060 master, slave scsi cabling
Does anyone know what the SCSI cabling should look like on the slave MSL6060
In a 2 unit configuration with the pass through mechanise?
Each MSL6060 has two Ultrium v3 drives and a NS e1200 тАУ 160 Fibre channel adapter both attached to different fabric switches (2\16 model)
Master Library SCSI cabling is as per section 8 in this document but as it only has two drives it looks like the top half of the 10u model.
I have also configured the master NSR as per section 10 but what about the one in the slave library?
TIA
Martin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2006 12:36 AM - last edited on тАО06-17-2021 08:29 AM by Parvez_Admin
тАО06-30-2006 12:36 AM - last edited on тАО06-17-2021 08:29 AM by Parvez_Admin
Re: msl6060 master, slave scsi cabling
The communication link between primary and secondary is done via ethernet and the special network hub - NOT via SCSI or FC.
There is also NO primary/secondary NSR.
Just cable the second box like the first and connect the FC from the NSR to your SAN switch.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2006 01:03 AM
тАО06-30-2006 01:03 AM
Re: msl6060 master, slave scsi cabling
If I assign the auto map to the NSR in the slave Library, I can see all four drive but get SCSI warnings on the slave library drives when I run the test option in LTT.
A small point that also that need qualifying the SCSI connector on the drives run Vertically one above the other, I am assuming that top and bottom is the same as if they ran horizontally?