- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: need correct dip switch settings for HP C5713 ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2004 05:55 AM - last edited on тАО03-09-2014 11:38 PM by Lisa198503
тАО01-14-2004 05:55 AM - last edited on тАО03-09-2014 11:38 PM by Lisa198503
need correct dip switch settings for HP C5713 DDS4 AutoLoader
I am having problems getting my scsi card to recognize my autoloader. There are some dip settings on the bottom of the autoloader unit that I'm wondering how they should be set. I'm running Windows 2000 and using a scsi adaptec 2940uw. Does anybody have any suggestions?
P.S. This thread has been moved from Disk to Tape Libraries and Drives. -HP Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2004 07:21 AM
тАО01-14-2004 07:21 AM
Re: need correct dip switch settings for HP C5713 DDS4 AutoLoader
But if you have problem getting the SCSI Card to see the drive,
There are few things that can check:
1: make sure the SCSI card is connected on the 1st or 2nd PCI Slot ├в A Bus-mastering slot.├в
2: Make sure the Scsi Card is detected OK
3: make sure drive is terminated, and check the cable and the termination for bent pins ├в which is the most common reason why a Scsi card does not see a drive├в
and see if that would
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2004 04:21 PM
тАО01-14-2004 04:21 PM
Re: need correct dip switch settings for HP C5713 DDS4 AutoLoader
If so, then you need to enable Multiple LUN support in the SCSI card bios.
If the drive doesn't appear in the OS, does anything appear during boot when the SCSI card bios lists the devices it finds?
The switches on the bottom don't affect whether the device appears on the SCSI bus (although they can change the inquiry string). For default behavior, they should be all on except 3 (which disables MRS).
You also have an autocloader option switch on the back which should be set to 7, and the autoloader SCSI ID which should be anything except 7 (which is the HBA).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2004 03:22 AM
тАО01-15-2004 03:22 AM
Re: need correct dip switch settings for HP C5713 DDS4 AutoLoader
Are there perhaps some settings I should be looking at on the scsi card itself?
Currently I have the following settings:
host adaptor scsi id: 7
SCSI Parity checking: Enabled
Host Adaptor SCSI termination: Automatic
On Boot Device Options: Boot Target ID:0
Initiate Sync Negotiation: yes
Max Sync Transfer rate: 40.0
Enable disconnection: yes
initiate wide negotiation: yes
Plug and Play scan support: disabled
host adaptor bios: disabled
support removable disks under bios as fixed disks: disabled
Extended bios translation for DOS > 1 gig: disabled
Multiple lun support disabled
bios support for bootable CD-Rom: disabled
support for ultra scsi speed: enabled
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2004 03:34 AM
тАО01-15-2004 03:34 AM
Re: need correct dip switch settings for HP C5713 DDS4 AutoLoader
The SCSI ID should should be anything EXCEPT 7 which is the HBA controller ID.
Autoloader options -> 7
Autoloader SCSI Id -> Anything except 7
Autoloader DIP switches -> all On, except #3
How is it cabled and what kind of terminator are you using?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2004 05:20 AM
тАО01-15-2004 05:20 AM
Re: need correct dip switch settings for HP C5713 DDS4 AutoLoader
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2004 06:04 AM
тАО01-15-2004 06:04 AM
Re: need correct dip switch settings for HP C5713 DDS4 AutoLoader
If you already tried what I suggested before and still no luck
Try another cable, or/and another Scsi card
Or try connecting another Scsi device on the Scsi card.