- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: vs80 Autoloader drivers
StoreEver Tape Storage
1752290
Members
5083
Online
108786
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-09-2004 09:47 AM
07-09-2004 09:47 AM
vs80 Autoloader drivers
I have a vs80 DLT Autoloader installed on a n-class hp server with hpux 11.11. I use Openview Data Protector(OmniBack) Ver. A.05.10
for backups. When I ran the auto config the robotics listed as a DLT device with no drive,
and the drive listed seperatly as a lto/ ultrium device. When I change the drive to a DLT unit it will not read tapes when I run a scan, but the robotics work. When I change the Robotics and Drive to lto/ultrium devices I ran a successfull scan. Could this be because the wrong driver was loaded for the drive unit, or could the drive unit in the autoloader be a lto/ultrium drive? How could I found out which is the problem?
Thank you in advance for any help.
Chris Lozano
for backups. When I ran the auto config the robotics listed as a DLT device with no drive,
and the drive listed seperatly as a lto/ ultrium device. When I change the drive to a DLT unit it will not read tapes when I run a scan, but the robotics work. When I change the Robotics and Drive to lto/ultrium devices I ran a successfull scan. Could this be because the wrong driver was loaded for the drive unit, or could the drive unit in the autoloader be a lto/ultrium drive? How could I found out which is the problem?
Thank you in advance for any help.
Chris Lozano
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-12-2004 02:21 AM
07-12-2004 02:21 AM
Re: vs80 Autoloader drivers
Hi,
For DataProtector 5.0 you must manually enter the device file for the tape drive only. e.g. /dev/rmt/c4t5d0BESTb. My guess is that you still must do this for 5.1.
To verify run ioscan the tape drive and autoloader show up as LUN 0 and LUN 1.
Ron Sutton
For DataProtector 5.0 you must manually enter the device file for the tape drive only. e.g. /dev/rmt/c4t5d0BESTb. My guess is that you still must do this for 5.1.
To verify run ioscan the tape drive and autoloader show up as LUN 0 and LUN 1.
Ron Sutton
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP