Web and Unmanaged
cancel
Showing results for 
Search instead for 
Did you mean: 

1920-16g switch config

yldzyalcin
Visitor

1920-16g switch config

I have a 1920-16g switch and I want to configure it for routing my network.

I have a plc with ethernet and I have a other network device.

My PLC ip address is:192.168.1.71 255.255.255.0

      other device ip is: 192.168.100.100 255.255.0.0

and I dont have a gateway device. How I configure my hpe?

6 REPLIES
HP-Browniee
Respected Contributor

Re: 1920-16g switch config

Hi

First of all your client needs a gateway if you want to route between vlans. 

And second, the 1920 switch is not a routing switch. The only thing it supports is static routes.

Kind regards

16again
Respected Contributor

Re: 1920-16g switch config

For sure the 1920 is a routing switch, since  it can route among VLANs and to static routes, whereas a layer 2 switch can only switch packets onto the .

If you hack yourself into the CLI.....you'll find as an undocumented feature both ripv2 and ospf routing protocols.

yldzyalcin
Visitor

Re: 1920-16g switch config

thank you for your reply.

I will try but I'm beginer for this topic.

HP-Browniee
Respected Contributor

Re: 1920-16g switch config

@16again Like i said it only supports static routes. I'm pretty sure that ospf will not be possible on this type of switch, even in the CLI.

Kind regards

16again
Respected Contributor

Re: 1920-16g switch config

I'm also pretty sure....seeing is believing:  (for the ospf commands, just look into H3C S-5500-SI_Manual_V1.03.pdf  and try on 1920)


[hp1920]display ospf peer

                  OSPF Process 100 with Router ID 0.0.19.20
                        Neighbor Brief Information

 Area: 0.0.0.0
 Router ID       Address         Pri  Dead-Time  Interface       State
 10.31.76.249    10.31.76.249    1    34         Vlan333         Full/BDR
[HP1920]display ip routing-table
Routing Tables: Public
        Destinations : 15       Routes : 15

Destination/Mask    Proto  Pre  Cost         NextHop         Interface

0.0.0.0/0           Static 1    0            10.31.76.253    Vlan333
10.0.0.0/8          OSPF   110  21           10.31.76.249    Vlan333
10.31.76.0/26       Direct 0    0            10.31.76.62     Vlan330
10.31.76.62/32      Direct 0    0            127.0.0.1       InLoop0
10.31.76.64/26      Direct 0    0            10.31.76.126    Vlan331
10.31.76.126/32     Direct 0    0            127.0.0.1       InLoop0
10.31.76.128/27     Direct 0    0            10.31.76.158    Vlan332
10.31.76.158/32     Direct 0    0            127.0.0.1       InLoop0
10.31.76.192/26     Direct 0    0            10.31.76.254    Vlan333
10.31.76.254/32     Direct 0    0            127.0.0.1       InLoop0
127.0.0.0/8         Direct 0    0            127.0.0.1       InLoop0
127.0.0.1/32        Direct 0    0            127.0.0.1       InLoop0
172.16.0.0/12       OSPF   110  21           10.31.76.249    Vlan333
172.30.121.0/24     O_ASE  110  41           10.31.76.249    Vlan333
192.168.0.0/16      O_ASE  110  20           10.31.76.249    Vlan333

yldzyalcin
Visitor

Re: 1920-16g switch config

tahank you for your interest, I solved the problem. It's working now and dont need a default gateway.