- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Web and Unmanaged
- >
- Re: 802.1x on HP switch
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 06:45 AM - last edited on 05-04-2015 08:30 PM by Maiko-I
05-04-2015 06:45 AM - last edited on 05-04-2015 08:30 PM by Maiko-I
802.1x on HP switch
Dear ALL,
I'm configuring 802.1x on HP procurve V1910 switch following the HP configuration guide but clients fails to authenticate NPS server (WS 2012). I has been configing with other Cisco 2960 and HP 2620, both worked without any problem. I have 2 HPv1910 switches and both have the same issue.
On NPS server's log i got error event ID 13: "A RADIUS message was received from the invalid RADIUS client IP address xxx1"
Here is the switch config which i extracted main parts:
domain default enable system
#
ip ttl-expires enable
#
dot1x
dot1x authentication-method eap
#
password-recovery enable
#
vlan 1
#
vlan 50
#
vlan 60
#
vlan 81
#
radius scheme system
server-type extended
primary authentication xxx1
primary accounting xxx1
key authentication cipher $c$3$4IF6hoCQIHbz8cxRpCzqh7ROM0ITkcTY2M0daszn7/Ic
key accounting cipher $c$3$aAj7S8b+d3Yxx1ncQU+6CSuekiAFklUxQ9C4BusqY5ou
security-policy-server xxx1
timer response-timeout 5
user-name-format without-domain
nas-ip xxx.2
# switch-ip
retry 5
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
user-group system
#
local-user admin
password cipher $c$3$6D7SFA/cDC+o9YomMrhinWX+/tFAOkgNBA==
authorization-attribute level 3
service-type ssh telnet terminal
service-type ftp
service-type web
#
stp mode rstp
stp enable
...
interface GigabitEthernet1/0/5
port access vlan 1
stp edged-port enable
dot1x re-authenticate
dot1x guest-vlan 81
dot1x auth-fail vlan 81
dot1x port-method portbased
dot1x port-control auto
dot1x
...
#
ssh server enable
#
user-interface aux 0
authentication-mode scheme
user-interface vty 0
authentication-mode none
user privilege level 2
idle-timeout 2 0
protocol inbound telnet
user-interface vty 1 15
authentication-mode scheme
I tried to upgrade firmware but i suppose it wasn't the cause (current firmware version 5.20 Release 1513P85). Any help would be appreciated!
Thanks guy!
P.S. This thread has been moved from HP Networking to Web and Unmanaged. - Hp Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 10:15 PM
05-04-2015 10:15 PM
Re: 802.1x on HP switch
What's wrong with my post, it is a security issue but moved to Web and unmanaged category ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2015 07:46 PM
05-10-2015 07:46 PM
Re: 802.1x on HP switch
So there is no support from HP in my case ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2015 03:53 AM
05-11-2015 03:53 AM
Re: 802.1x on HP switch
>So there is no support from HP in my case?
This is a peer to peer forum, not an official HP support site.
Have you tried contacting the HPSC?
http://www.hp.com/go/hpsc