- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Module not present for port or invalid port - ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2012 02:34 AM
тАО10-29-2012 02:34 AM
Hi,
I'm having some trouble with one specific port in my zl5406 switch.
The ports is at my desk, i use it for configuring access-points and so on.
Everytime i try to move the port into another VLAN i get this error:
"Module not present for port or invalid port: a14"
As i said, its only for this port, and it is up, and working, sending out PoE to my access-point.
Any ideas?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2012 09:10 AM
тАО10-29-2012 09:10 AM
Re: Module not present for port or invalid port - only for one specific port
What does the output of a "show mod" give you?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2012 10:18 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-30-2012 01:28 AM
тАО10-30-2012 01:28 AM
Re: Module not present for port or invalid port - only for one specific port
It seems i was in a trunk, and now that i think of it, i used it for some trunking tests before the summer - totally fogot!
Thank you for your answers, it is much appriciated!
/Mick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-31-2012 01:43 AM
тАО10-31-2012 01:43 AM
Re: Module not present for port or invalid port - only for one specific port
No problem Mick, I have done that enough times and wondered why the switch doesn't see the individual port ;)
All the best
Don't forget to mark a post resolved if your question was answered.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2018 04:30 AM
тАО04-30-2018 04:30 AM
Re: Module not present for port or invalid port - only for one specific port
I have this same error when attempting to use the show interface trunk-utilization command as recommended by HP in the release notes for the KB.16.02.0013 firmware. KB.16.02.0013 release notes.
I have three trunks configured on the switch but am getting this message when attempting to look at a specific trunk's utilisation. Do you know why I would be getting this message in this instance?
Thanks