- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: BL P Class Enclosure - Slot issues
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-24-2009 05:02 AM
тАО12-24-2009 05:02 AM
There is no Fault alarms indicated in the enclosure and power enclsoure also.
how to resolve this slot issues..
note - two enclosures have the same slot issues.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-24-2009 11:00 AM
тАО12-24-2009 11:00 AM
Re: BL P Class Enclosure - Slot issues
Maybe the power converter module inside the blade has failed. I would replace it to see if it helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-24-2009 03:47 PM
тАО12-24-2009 03:47 PM
Re: BL P Class Enclosure - Slot issues
change power converter & dc filter together ,
if you do not change then together they will fry each other ,this is common issue , i am presuming you have not changed hardware configuration of blade lately.
This is how we thank each other in the forum
http://forums11.itrc.hp.com/service/forums/helptips.do?#33
Enjoy:)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-26-2009 07:48 PM
тАО12-26-2009 07:48 PM
Re: BL P Class Enclosure - Slot issues
In most of my cases , just replace blase server system board and fixed the problem.
If PPM or VRM failed , the health LED will shows red.
Regards.
Terence
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-26-2009 09:20 PM
тАО12-26-2009 09:20 PM
Re: BL P Class Enclosure - Slot issues
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2009 08:46 AM
тАО12-27-2009 08:46 AM
Re: BL P Class Enclosure - Slot issues
Did you reset server management module and power management module during these days ? If you have done all hw check , maybe the server enclosure backplane should put into test.
Regards.
Terence
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2009 10:58 AM
тАО12-27-2009 10:58 AM
Re: BL P Class Enclosure - Slot issues
If reset doesn't work work then which one do i need to replace ?? Management module or Power Module ???
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2009 10:05 PM
тАО12-27-2009 10:05 PM
SolutionPlease refer to attached file , tou will see 2 kinds of management module.
You can reser each of them , reset them wouldn't cause production servers shutdown or anything else.These 2 modules are hot plugable.
If reset module still doesn't work , perhaps we need to check or replace power backplane board , see page 1.
Regards.
Terence
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2009 11:22 PM
тАО12-27-2009 11:22 PM
Re: BL P Class Enclosure - Slot issues
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2009 11:55 PM
тАО12-27-2009 11:55 PM
Re: BL P Class Enclosure - Slot issues
Please refer to attached.
Hope it useful.
Regards.
Terence