- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: bl20p g3 power pinout
BladeSystem - General
1753716
Members
4768
Online
108799
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-25-2007 08:30 PM
тАО11-25-2007 08:30 PM
bl20p g3 power pinout
I need to build a stand alone test rig for bl20p g3s.
There is a 4 pin power connector on the rear of the bl20p. I can see the two center pins are common , and the two outside ones independent.
Does anyone know the pinout for this connector?
Many thanks in adavnce
Matt
Many thanks
There is a 4 pin power connector on the rear of the bl20p. I can see the two center pins are common , and the two outside ones independent.
Does anyone know the pinout for this connector?
Many thanks in adavnce
Matt
Many thanks
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-29-2007 02:23 AM
тАО11-29-2007 02:23 AM
Re: bl20p g3 power pinout
HP has a stand alone diagnostic center for the p-Class blades. Here is a link to the users guide
http://docs.hp.com/en/230859-004/230859-004.pdf
http://docs.hp.com/en/230859-004/230859-004.pdf
No support by private messages. Please ask the forum!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2007 08:39 AM
тАО12-05-2007 08:39 AM
Re: bl20p g3 power pinout
Thanks for your reply,
but I couldn't find pin out information in the maual your recommended.
Does anyone know the power pinout for this system?
many thanks.
Matt
but I couldn't find pin out information in the maual your recommended.
Does anyone know the power pinout for this system?
many thanks.
Matt
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP