- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- BL460 blades unable to connect
BladeSystem - General
1753363
Members
5077
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-06-2007 01:20 AM
04-06-2007 01:20 AM
BL460 blades unable to connect
Hello all,
I have the following hardware and something seems to be up with the eth ports on my blade or the interconnect blade. I am not totally sure where the problem lays. In Redhat the drivers appear to load fine (bcnx2) but no matter what I do I cannot get any connectivity. I do not get any link lights on either the switch or the interconnect card. I have tried going to a different switch and used several different cables with no luck. any direction on this problem would be appreciated because I am out of ideas.
Thanks,
-Todd
Hardware List:
Chasis c-class: 412152-B21 FW: 1.01
Admin module: 416000-001
Blade (bl460): 404664-B21
Interconnect: 406740-B21
I have the following hardware and something seems to be up with the eth ports on my blade or the interconnect blade. I am not totally sure where the problem lays. In Redhat the drivers appear to load fine (bcnx2) but no matter what I do I cannot get any connectivity. I do not get any link lights on either the switch or the interconnect card. I have tried going to a different switch and used several different cables with no luck. any direction on this problem would be appreciated because I am out of ideas.
Thanks,
-Todd
Hardware List:
Chasis c-class: 412152-B21 FW: 1.01
Admin module: 416000-001
Blade (bl460): 404664-B21
Interconnect: 406740-B21
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-06-2007 01:28 AM
04-06-2007 01:28 AM
Re: BL460 blades unable to connect
This problem was due to the fact that all the switches I used were NOT gigE switches. Plugged it into a GigE switch and it came right up.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP