- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: BL460c G1 - No scsi controller on reboot
BladeSystem - General
1753481
Members
4543
Online
108794
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2009 01:35 PM
тАО08-20-2009 01:35 PM
BL460c G1 - No scsi controller on reboot
Hi,
We have 3 or so Blades that when we reboot them (for whatever reason) they sometimes just go to PXE boot and can't see the e200i controller.
I can get round this by using the iLO to power the unit off and back on but is this a known issue and fixable?
Thanks
Jase
We have 3 or so Blades that when we reboot them (for whatever reason) they sometimes just go to PXE boot and can't see the e200i controller.
I can get round this by using the iLO to power the unit off and back on but is this a known issue and fixable?
Thanks
Jase
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2009 11:04 PM
тАО08-20-2009 11:04 PM
Re: BL460c G1 - No scsi controller on reboot
What firmwares are in use
ILO,OA,server bios, smart array ?
ILO,OA,server bios, smart array ?
Remember to give Kudos to answers! (click the KUDOS star)
You can find me from Twitter @JKytsi
You can find me from Twitter @JKytsi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-21-2009 12:38 AM
тАО08-21-2009 12:38 AM
Re: BL460c G1 - No scsi controller on reboot
The connector for the mezz card that the drivers and arrary controller connect to the main board with may need reseating as well.
Push hard on the yellow sticker or blue plastic bit.
Push hard on the yellow sticker or blue plastic bit.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP