- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: c3000 power supply error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-16-2008 11:27 PM
тАО06-16-2008 11:27 PM
c3000 power supply error
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-17-2008 04:46 AM
тАО06-17-2008 04:46 AM
Re: c3000 power supply error
Check the "Power and Thermal" and all three items below it on the OA menu. "Power management", "Enclosure Power Allocation" and "Power meter". They should tell you if you need additional power supplies.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-18-2008 02:11 AM
тАО06-18-2008 02:11 AM
Re: c3000 power supply error
place the second blade in slot 5 (lower right). You have only 2 power supplies which are at the bottom slot. For Blades in Slot 2 or 6 you need two additional power supplies in the middle of the power slots.
Thomas
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-24-2008 01:37 PM
тАО06-24-2008 01:37 PM
Re: c3000 power supply error
You see this problem when you have Set Power management set to AC Redundant or Power Supply Redundant, And 2 blades request power at the same time.
During that time Blade in slot 2 may show that Insufficient Enclosure power to Poweron error.
The moment Blade one comes up it will release the extra power and the second Blade will power on. So no need to worry in your case since you have only 2 blades.
Still if you don't want to see the errors please change the Power management settings to Not Redundant. It should work fine.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-08-2008 10:05 AM
тАО07-08-2008 10:05 AM
Re: c3000 power supply error
however that issue gone away with fw upgrade of the OA.
Is a known issue