- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: connecting BL860c to an External Storage
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2008 01:54 PM
тАО12-17-2008 01:54 PM
Do I also need Cisco MDS 9142 switch...
or can I connect this Clarion directly to the Cisco 3020 switch provided with the Blade Enclosure...
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 04:20 AM
тАО12-18-2008 04:20 AM
SolutionHope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 06:58 AM
тАО12-18-2008 06:58 AM
Re: connecting BL860c to an External Storage
My Issue is with the switch which needs to be configured...
fc1/1 is down (Error disabled - bit error rate too high)
Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)
Port WWN is 20:01:00:0d:ec:68:80:00
Admin port mode is auto, trunk mode is on
snmp link state traps are enabled
Port vsan is 1
Receive data field Size is 2112
Beacon is turned off
5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
977 frames input, 39504 bytes
0 discards, 1 errors
0 CRC, 0 unknown class
0 too long, 1 too short
22 frames output, 1356 bytes
0 discards, 0 errors
1 input OLS, 1 LRR, 0 NOS, 5 loop inits
2 output OLS, 0 LRR, 0 NOS, 1 loop inits
I did some google on this... but couldn't find much
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 07:25 AM
тАО12-18-2008 07:25 AM
Re: connecting BL860c to an External Storage
Error Message PORT-5-IF_DOWN_BIT_ERR_RT_THRES_EXCEEDED: Interface [chars] is down (Error disabled - bit error rate too high)
Explanation The port has detected too high bit error rate in frames received from attached device
Recommended Action Check the attached device; replace it if needed
But as of Now only the storage Clarion is connected to the Switch MDS 9124. I haven't connected the switch to the blade yet....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 07:39 AM
тАО12-18-2008 07:39 AM
Re: connecting BL860c to an External Storage
-------------
2008 Dec 17 16:38:24 9103 %PORT-5-IF_DOWN_BIT_ERR_RT_THRES_EXCEEDED: %$VSAN
1%$ Interface fc1/1 is down (Error disabled - bit error rate too high)
2008 Dec 17 16:38:24 9103 %MODULE-4-MOD_WARNING: Module 1 (serial: JAE11506S
GY) reported warnings on ports 1/1-1/1 (Fibre Channel) due to MAC Bit error exce
eded threshold in device 92 (device error 0xc5c00503)
and on the other switch i have the following
errors:-
2008 Dec 17 12:17:02 9104 %MODULE-4-MOD_WARNING: Module 1 (serial: JAF1204BB
BB) reported warnings on ports 1/11-1/11 (Fibre Channel) due to FC MAC Experienc
ed an error in device 92 (device error 0xc5c0025d)
2008 Dec 17 12:17:11 9104 %MODULE-4-MOD_WARNING: Module 1 (serial: JAF1204BB
BB) reported warnings on ports 1/11-1/11 (Fibre Channel) due to FC MAC Experienc
ed an error in device 92 (device error 0xc5c0025d)
2008 Dec 17 13:34:53 9104 %MODULE-4-MOD_WARNING: Module 1 (serial: JAF1204BB
BB) reported warnings on ports 1/9-1/9 (Fibre Channel) due to FC MAC Experienced
an error in device 92 (device error 0xc5c0025d)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 08:11 AM
тАО12-18-2008 08:11 AM
Re: connecting BL860c to an External Storage
fc1/3 is up
Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN
Port WWN is 20:03:00:0d:ec:68:80:00
Admin port mode is auto, trunk mode is on
snmp link state traps are enabled
Port mode is F, FCID is 0xae0100
Port vsan is 1
Speed is 2 Gbps
Rate mode is dedicated
Transmit B2B Credit is 8
Receive B2B Credit is 16
Receive data field Size is 2112
Beacon is turned off
5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
Now the issue is my Blade server is not recognizing the disks.......
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 08:33 AM
тАО12-18-2008 08:33 AM
Re: connecting BL860c to an External Storage
And the blade is not recognizing the luns
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 02:56 PM
тАО12-18-2008 02:56 PM
Re: connecting BL860c to an External Storage
1. Verify the blade port & the Clarion LUN are both logging into the SAN switch.
2. Put both in the same zone.
For the blade's FC HBA to login correctly you need the right QLogic or Emulex driver, fw and BIOS on the card.
Contact the HP SAN Switch team for further details, or reply back with the OS version & the FC HBA model (Emulex LPe1105 or QLA2462).