- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Fibre Mezzanine Not recognized by Windows
BladeSystem - General
1753784
Members
7229
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2008 12:17 PM
09-04-2008 12:17 PM
Fibre Mezzanine Not recognized by Windows
Hello,
I have a BL460C G1 on a c7000. When I go to the information tab, I can see the Emulex LPe1105-HP mezzanine card in slot 1. The port maapping to the interconnect bays look accurate and active.
The problem is, I cannot see the fibre card in windows. This is a Windows 2003 32 R2 install. It doesn't show up in the device manager, not is it seen by the storport mini driver wizard. I have re-installed windows a few times now.
Does anyone have any thoughts? I am just not sure if I have a bad fibre card
I have a BL460C G1 on a c7000. When I go to the information tab, I can see the Emulex LPe1105-HP mezzanine card in slot 1. The port maapping to the interconnect bays look accurate and active.
The problem is, I cannot see the fibre card in windows. This is a Windows 2003 32 R2 install. It doesn't show up in the device manager, not is it seen by the storport mini driver wizard. I have re-installed windows a few times now.
Does anyone have any thoughts? I am just not sure if I have a bad fibre card
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2008 12:27 PM
09-04-2008 12:27 PM
Re: Fibre Mezzanine Not recognized by Windows
Check this out you may be in the Similar problem:
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1236667
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1236667
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP