- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: ILO 2 not picking up HP Blade serial number or...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-15-2012 07:52 AM
02-15-2012 07:52 AM
ILO 2 not picking up HP Blade serial number or product ID
Version of ILO is 2.07
**This is a new blade and not a sysboard swap.**
ILO is not pulling the serial number or Product ID of the 2 new blades. I did not set these blades up. From my limited experience with ILO, I though this stuff is supposed to be set out of the box. All of the other blades in this enclosure are reporting correctly. Their ILO vesions are mixed, 3 v1.70s, 1 v2.01, and 1 v1.81
Any ideas on how to get this these tow blades ILO to capture this information?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-15-2012 07:53 AM
02-15-2012 07:53 AM
Re: ILO 2 not picking up HP Blade serial number or product ID
blades are 460 G6s
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-16-2012 03:06 AM
02-16-2012 03:06 AM
Re: ILO 2 not picking up HP Blade serial number or product ID
Ideally ilo2 fw and sys rom firmware has to be match according to the fw matrix and same across all the blades on the enclosure and shud be inline with OA firmware as it seems to me like a communication issue
here is the release set matrix
Regards,
Goutham Sabala
To assign points, click the Kudos Star!
Goutham Sabala
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-22-2012 08:47 PM - last edited on 03-26-2021 12:58 AM by Parvez_Admin
02-22-2012 08:47 PM - last edited on 03-26-2021 12:58 AM by Parvez_Admin
Re: ILO 2 not picking up HP Blade serial number or product ID
Open the blades up, and flip the reset pin on the motherboard ( I think it's pin 6, but double check that)
Insert and power up the blade, then pull it out again, and flip the pin back.
That should do a full reset of the motherboard and modules, and clear the issue.
We see this from time to time with refurb blades and "Illicit market" stuff.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-05-2012 06:56 AM
03-05-2012 06:56 AM
Re: ILO 2 not picking up HP Blade serial number or product ID
Check if the s/n and p/n is entered in the NVRAM.
Start the RBSU, in the information box, on the right side, you will see the s/n and p/n.
If not:
Enter the s/n and p/n manually.
Reset BIOS (From the RBSU), do not delete RAID.
Once you have done so.
Reset the ILo settings.
BR
/jag