- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- power down procedure for C7000
BladeSystem - General
1752808
Members
6131
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2009 11:36 PM
тАО01-15-2009 11:36 PM
I checked into the C7000. I don't see any power switches, therefore if I do need to power down the C7000, should I just unplug the power cords?
In addition, the "device power sequence" shown on the OA, is it ONLY used for determining the powerup sequence, and my blades do not have any dependency, I can just leave them disabled and will the blades be automatically come up after the C7000 has been up?
thanks
In addition, the "device power sequence" shown on the OA, is it ONLY used for determining the powerup sequence, and my blades do not have any dependency, I can just leave them disabled and will the blades be automatically come up after the C7000 has been up?
thanks
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2009 11:46 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-17-2009 12:45 AM
тАО01-17-2009 12:45 AM
Re: power down procedure for C7000
thanks.
Easy answer :-).
But does any know whether I need to "enable" the device power sequence? I know I can use that to order to power up sequence, but if I just want everything to come up, do I need to do anything?
Easy answer :-).
But does any know whether I need to "enable" the device power sequence? I know I can use that to order to power up sequence, but if I just want everything to come up, do I need to do anything?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-17-2009 04:49 AM
тАО01-17-2009 04:49 AM
Re: power down procedure for C7000
nope =)
Remember to give Kudos to answers! (click the KUDOS star)
You can find me from Twitter @JKytsi
You can find me from Twitter @JKytsi
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP