- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: After secondary processor install it only show...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-12-2019 12:10 PM
тАО12-12-2019 12:10 PM
After secondary processor install it only shows up at 243mhz and not the 1.4ghz
We just added a secondary processor to a BL860c I2 blade. THe primary processor is 1.4ghz and secondary is the pn# for the expansion cpu, however, the clock speed is only 243mhz during EFI Post.
IS the processor bad or is there something I have to run at the EFI Shell level or OS to get the cpu to be fully recognized?
OR is the processor bad?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-13-2019 07:36 AM - edited тАО12-13-2019 07:38 AM
тАО12-13-2019 07:36 AM - edited тАО12-13-2019 07:38 AM
Re: After secondary processor install it only shows up at 243mhz and not the 1.4ghz
Please send the captured output where you have seen this.
Please connect to MP/ILO and do
CM:hpiLO-> sysrev
From running HP-UX please do
machinfo
should look like this:
# machinfo
CPU info:
Intel(R) Itanium(R) Processor 9340 (1.6 GHz, 20 MB)
4 cores, 8 logical processors per socket
4.79 GT/s QPI, CPU version E0
Active processor count:
8 sockets
32 cores (4 per socket)
32 logical processors (4 per socket)
LCPU attribute is disabled
... or this
# /usr/contrib/bin/machinfo
CPU info:
32 Intel(R) Itanium 2 9000 series processors (1.6 GHz, 18 MB)
533 MT/s bus, CPU version C2
64 logical processors (2 per socket)
Memory: 523770 MB (511.49 GB)
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-15-2019 11:20 AM
тАО12-15-2019 11:20 AM
Re: After secondary processor install it only shows up at 243mhz and not the 1.4ghz
Please share the following to verify. (capture it in a text file adn attach here)
1.MP > CM > df -all -nc
2.MP > CM > sysrev
Also, as requested earlier, share the "machinfo" output as well.
Thanks
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-24-2019 09:22 AM
тАО12-24-2019 09:22 AM
Re: After secondary processor install it only shows up at 243mhz and not the 1.4ghz
Hi,
Please open a Support ticket with MP logs to validate.
Thanks
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]