- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Bridge Port Data Units (BPDU) Filter and Link Agr...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-09-2012 08:28 AM
05-09-2012 08:28 AM
Bridge Port Data Units (BPDU) Filter and Link Agregation Control Protocol (LACP) questions?
Andre is helping a customer that is connecting Virtual Connect to a Cisco Nexus switch:
*****************
Hi guys,
This is the last configuration of the customer on the Nexus :
Eth10/30 vs HP_prod. Cloud connected trunk full 10G 10Gbase-SR
Eth10/31 vs HP_prod. Cloud suspnd trunk full auto 10Gbase-SR
interface port-channel10
description LAG HP_prod. Cloud Engine
switchport
switchport mode trunk
spanning-tree port type edge trunk
interface Ethernet10/30
description vs HP_prod. Cloud Engine
switchport mode trunk
channel-group 10 mode active
no shutdown
interface Ethernet10/31
description vs HP_prod. Cloud Engine
switchport mode trunk
channel-group 10 mode active
no shutdown
Debug LACP
2012 May 8 20:11:45.284731 lacp: lacp_proto_get_state(731): IF Ethernet10/30(0x1a49d000): end PartnerEnd(2): state TimeOut(1): enable_flag True
2012 May 8 20:11:44.844591 lacp: lacp_proto_get_state(731): IF Ethernet10/31(0x1a49e000): end PartnerEnd(2): state TimeOut(1): enable_flag True
The problem is that the VC doesn’t answer to the LACP request, the firmware of the VC is 3.18 because the customers had urgency to go in production, but I think it’s not the problem.
******************
Reply from David:
******************
Look at this guide: http://h20000.www2.hp.com/bc/docs/support/SupportManual/c02656171/c02656171.pdf
As per the guide, have you tried:
- LACP rate Fast?
- Reviewed the Cisco fw?
interface port-channel10
description LAG HP_prod. Cloud Engine
LACP rate Fast
switchport
switchport mode trunk
spanning-tree port type edge trunk
interface Ethernet10/30
description vs HP_prod. Cloud Engine
LACP rate Fast
switchport mode trunk
spanning-tree port type edge trunk
channel-group 10 mode active
no shutdown
interface Ethernet10/31
description vs HP_prod. Cloud Engine
LACP rate Fast
switchport mode trunk
spanning-tree port type edge trunk
channel-group 10 mode active
no shutdown
****************
Any other suggestions?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2012 08:22 AM
05-11-2012 08:22 AM
Re: Bridge Port Data Units (BPDU) Filter and Link Agregation Control Protocol (LACP) questions?
Reply back from Andrea:
**************
That was the answer I needed.
I’ve been on site and I verified a cabling problem (exchanged 2 VC cables directed to different Nexus).
Now everything works.
***************