- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- A5800 and HP X110 100M SFP LC FX Transceiver (JD10...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-03-2013 05:45 PM
02-03-2013 05:45 PM
A5800 and HP X110 100M SFP LC FX Transceiver (JD102B)
I recently installed a HP X110 into an A5800 switch. I am unable to obtain a link with this module. The other end is a known working 100M FX fibre converter.
Displaying the interface results in the following:-
Ten-GigabitEthernet1/0/51 current state: DOWN
IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 0023-8957-5fbb
Loopback is not set
Media type is optical fiber,Port hardware type is 100_BASE_SX_SFP
Why does it say the hardware type is 100_BASE_SX? It should be FX. I checked the model no. etc of the transceiver and it is correct. I know it is a H3C transceiver with a HP sticker over the top so I am wondering if it is actually an incorrect module? I would have expected 1000_BASE_SX though if it was incorrect.
Does anyone have a 100FX module installed that can advise of their configuration output please?
James.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2013 01:24 AM
02-04-2013 01:24 AM
Re: A5800 and HP X110 100M SFP LC FX Transceiver (JD102B)
Are you sure the SFP+ slots in the 5800 even supports 100Mbit? The datasheet says they are 1000/10000 ports. Can't say that I've tested myself though.
CCIE Service Provider
MASE Network Infrastructure [2011]
H3CSE
CCNP R&S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2013 07:08 AM
02-04-2013 07:08 AM
Re: A5800 and HP X110 100M SFP LC FX Transceiver (JD102B)
Possibly they only work with the 16 port SFP module, then.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2013 02:48 PM
02-04-2013 02:48 PM
Re: A5800 and HP X110 100M SFP LC FX Transceiver (JD102B)
Te1/0/51 sounds like a on-board interface.
CCIE Service Provider
MASE Network Infrastructure [2011]
H3CSE
CCNP R&S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2013 05:00 PM
02-04-2013 05:00 PM
Re: A5800 and HP X110 100M SFP LC FX Transceiver (JD102B)
1/0/51 is the 3rd sfp+ port. It's a real port and as you can see from the config it can see the module.
The module is listed as compatible according to the accessories page at http://h17007.www1.hp.com/us/en/products/switches/HP_5800_Switch_Series/index.aspx#JD102B
James.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2013 10:51 PM - edited 02-04-2013 10:51 PM
02-04-2013 10:51 PM - edited 02-04-2013 10:51 PM
Re: A5800 and HP X110 100M SFP LC FX Transceiver (JD102B)
If you look at that same page under Models you'll also see "4 fixed 1000/10000 SFP+ ports" mentioned on all models. Are you able to configure "speed 100" on the interface?
I think Richard was right and the reason that the 100Mbit SFP is listed as compatible on the accessories page is that it might be compatible with the "HP 5800 16-port SFP Module (JC095A)" module. Call your HP rep and make sure.
CCIE Service Provider
MASE Network Infrastructure [2011]
H3CSE
CCNP R&S