- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Issue regarding my HP MSA1500
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 05:09 AM - last edited on 02-23-2012 10:41 PM by Ajay-Kumar
02-23-2012 05:09 AM - last edited on 02-23-2012 10:41 PM by Ajay-Kumar
Issue regarding my HP MSA1500
I am using HP MSA1500
I have aArray H consist of 4 disks with RAID1+0
In order to expand the array I have mistakenly added 1 drive to the array which gives me kind of message that your array is RAID1
0 and some thing I dont remember ,
But I pressed Ok to that message and Now the array is showing trasnforming status and RAID6 ADG and after 2 hours it just gone to 1%.
The Array was having 2 logical drive and I checked the servers where the drives are presented and its looking OK. i can see the data there but I am worried if the data will be lost
Please advice, if MSA will change the Array RAID with out destrying the data
Or what can i do to revert back to the situation
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 05:32 AM
02-23-2012 05:32 AM
Re: PLEASE HELP
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 05:32 AM
02-23-2012 05:32 AM
Re: PLEASE HELP
I would not have expected ACU to allow that to occur.
Your data is fine, you will have to let the expansion run its course to completion.
If you want revert back to the previous configuration. You will have to delete, recreate and restore. Make sure you have fresh backup copies.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 06:02 AM
02-23-2012 06:02 AM
Re: PLEASE HELP
Thank you Guys.
Thats a big releif. I am keeping my finger cross for successfull completion, but its very slow.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 06:11 AM
02-23-2012 06:11 AM
Re: PLEASE HELP
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 06:20 AM
02-23-2012 06:20 AM
Re: PLEASE HELP
I have no problem there with time as far as the data is good and intact. Which I hope it will be ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 10:25 AM
02-23-2012 10:25 AM
Re: PLEASE HELP
After expansion you can run a file system check to confirm the integrity of the data.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2012 11:37 AM
02-23-2012 11:37 AM
Re: PLEASE HELP
its been more than 8 hours but it is still on 1%
i will be moving off data from the servers but will need at least 24 hours for robocopy and other change managment time. I hope this should allow me that much time beofre every thing falls apart :(