- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- ILO does not work!
Server Management - Remote Server Management
1748282
Members
3908
Online
108761
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-17-2009 09:12 PM
06-17-2009 09:12 PM
ILO does not work!
I am a newbie to HP server. Now I have two DL180 G5.
I set the IP address, Net MASK and gateway address to their ILOs.
The setting is like Below
DHCP IP Source [static]
IP Address [192.168.1.8]
Subnet Mask [255.255.255.0]
Default Gateway [192.168.1.1]
BMC Ping Response [Enable]
After configuration, I even loged into its ILO web page, http://iLOip
But the second day, I did not know what happened.
Ping iLO IP will get no response even I ping from the DL180 itself.
Is there any one know the reason or meet the same problem.
Any help will be appreciated very much.
I set the IP address, Net MASK and gateway address to their ILOs.
The setting is like Below
DHCP IP Source [static]
IP Address [192.168.1.8]
Subnet Mask [255.255.255.0]
Default Gateway [192.168.1.1]
BMC Ping Response [Enable]
After configuration, I even loged into its ILO web page, http://iLOip
But the second day, I did not know what happened.
Ping iLO IP will get no response even I ping from the DL180 itself.
Is there any one know the reason or meet the same problem.
Any help will be appreciated very much.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-18-2009 05:53 PM
06-18-2009 05:53 PM
Re: ILO does not work!
I trust you did not use the same IP for the server and iLO or the same address for both iLOs. :)
Pinging iLO from the server or another machine is identical since the server does not communicate internally to the iLO via Ethernet. You can download and use the utility HPONCFG from this site and use it to attempt to reach iLO. If this is a Windows server I would also check to see in Device Manager whether the device has been disabled.
Good luck!
Pinging iLO from the server or another machine is identical since the server does not communicate internally to the iLO via Ethernet. You can download and use the utility HPONCFG from this site and use it to attempt to reach iLO. If this is a Windows server I would also check to see in Device Manager whether the device has been disabled.
Good luck!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP