- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- CPU is giving warning
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-06-2007 07:42 AM
тАО10-06-2007 07:42 AM
1. why i am not able to enter in CM(command menu). is Firmware version old which dont support command PS command
2. is there any other command by which i can check if CPU fan is working fine.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-06-2007 07:52 AM
тАО10-06-2007 07:52 AM
Re: CPU is giving warning
I don't know if you have the support tools installed, but if you have, you could run stm.
http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=B6191AAE
Regards,
Robert-Jan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-06-2007 08:49 AM
тАО10-06-2007 08:49 AM
Solutionto enter GSp just do a control b, you should be able to login and jsut do your PS command - no need for typing CM? if you were.
do you have permisions to allow you to use the gsp? you may need to reset the gsp if its not responding.
Also if you get in to the GSP, check the SS command aswell for the processor status.
we dont know if its an older version as you havent listed what you have installed?
Also there is no CPU fan in the L3000. there are 2/3 psu fans, a large front fan and rear fan and 4 io fans.
you may however have a bad platform monitor pca if everything is ok. or as you say may need the gsp firmware updating
Andy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-06-2007 08:20 PM
тАО10-06-2007 08:20 PM
Re: CPU is giving warning
Please do excute the below command .
#echo ├в selclass qualifier cpu;info;wait;infolog├в | /usr/sbin/cstm
Thanks,
Aneesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-07-2007 06:28 PM
тАО10-07-2007 06:28 PM
Re: CPU is giving warning
GSP> he li
HE LI
==== GSP Help ============================================(Administrator)===
AC : Alert display Configuration PC : Remote Power Control
AR : Automatic System Restart config. PG : PaGing parameter setup
CA : Configure asynch/serial ports PS : Power management module Status
CL : Console Log- view console history RS : Reset System through RST signal
CO : COnsole- return to console mode SDM : Set Display Mode (hex or text)
CSP : Connect to remote Service Proc. SE : SEssion- log into the system
DC : Default Configuration SL : Show Logs (chassis code buffer)
DI : DIsconnect remote or LAN console SO : Security options & access control
EL : Enable/disable LAN access SS : System Status of proc. modules
ER : Enable/disable Remote/modem TC : Reset via Transfer of Control
HE : Display HElp for menu or command TE : TEll- send a msg. to other users
IT : Inactivity Timeout settings VFP : Virtual Front Panel display
LC : LAN configuration WHO : Display connected GSP users
LS : LAN Status XD : Diagnostics and/or Reset of GSP
MR : Modem Reset XU : Upgrade the GSP Firmware
MS : Modem Status
Just run "PS". There is no CPU fan as mentioned above.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2007 05:30 PM
тАО10-08-2007 05:30 PM
Re: CPU is giving warning
Use the GSP>SL command for error logs to view the logs for troubleshooting.