- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- rp7410 - can't access BCH
HPE 9000 and HPE e3000 Servers
1753379
Members
5013
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2008 02:09 PM
тАО12-03-2008 02:09 PM
rp7410 - can't access BCH
We have one cell board in slot one (the bottom cell) - one core I/O in slot one (the bottom slot), two 36GB 15k HDs... at one point we had this server loaded with HP-UX. We had to change out CPU's and the RAM configuration.
Now we've lost the ability to get to the BCH to load the OS or even see a POST test...
We go to the >CO and see a prompt for what partition to use, or q for quit. We choose the partition and it hangs.
Should we try and use a terminal emulator to try and upgrade all the firmware on the system? I ran a >CM:SYSREV and the firmware numbers were not all the same...
Now we've lost the ability to get to the BCH to load the OS or even see a POST test...
We go to the >CO and see a prompt for what partition to use, or q for quit. We choose the partition and it hangs.
Should we try and use a terminal emulator to try and upgrade all the firmware on the system? I ran a >CM:SYSREV and the firmware numbers were not all the same...
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2008 05:56 PM
тАО12-03-2008 05:56 PM
Re: rp7410 - can't access BCH
hi,
from mp, run sl and choose to view errors messages. WOuld be useful if you could post the errors here.
from mp, run sl and choose to view errors messages. WOuld be useful if you could post the errors here.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-04-2008 02:17 PM
тАО12-04-2008 02:17 PM
Re: rp7410 - can't access BCH
It turned out to be a couple of bad processors. Thanks.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP