- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- HPE Aruba Networking & ProVision-based
- >
- Procurve 2920-24G show incorrect Time/Date in logs
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-27-2015 12:57 PM - edited 01-27-2015 01:23 PM
01-27-2015 12:57 PM - edited 01-27-2015 01:23 PM
Procurve 2920-24G show incorrect Time/Date in logs
Hi, How do I set the correct Time & Date in this switch? I cannot find any options to set the Time & Date in the GUI
Edit: I have just installed the latest software: WB.15.16.0005
I get the following messages when logging in today (27 Jan 2015):
"Your previous successful login (as manager) was on 1990-02-05 00:14:39 from 192.168.x.x"
The first log entry is:
"Sun Feb 4 23:52:38 1990 Info First time installation Important installation information for your switch"
/CWTech
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-28-2015 04:31 PM
01-28-2015 04:31 PM
Re: Procurve 2920-24G show incorrect Time/Date in logs
I've never looked at the GUI, but it should allow you to configure an NTP server in the basic configuration page, usually below where you configure hostname.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-20-2015 12:59 PM
10-20-2015 12:59 PM
Re: Procurve 2920-24G show incorrect Time/Date in logs
I have always set it from the command line.
conf t
time mm/dd/yyyy
time hh:mm:ss
wr mem
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2015 05:51 AM - edited 10-22-2015 05:57 AM
10-22-2015 05:51 AM - edited 10-22-2015 05:57 AM
Re: Procurve 2920-24G show incorrect Time/Date in logs
Thanks, I've already solved the issue mentioned in my first post by using these commands:
Syntax:
time timezone <-720 - 840> time daylight-time-rule <none |alaska |
continental-us-and-canada | middle-europe-and-portugal | southern-hemisphere |
western-europe | user-defined>
East of the 0 meridian, the sign is "+". West of the 0 meridian, the sign is "-". For example, the time zone setting for Berlin, Germany is +60 (zone +1, or 60 minutes), and the time zone setting for Vancouver, Canada is -480 (zone -8, or -480 minutes).
To configure the time zone and daylight time rule for Vancouver, Canada:
HP Switch(config)# time timezone -480 daylight-time-rule continental-us-and-canada
For Europe:
HP Switch(config)# time timezone +60 daylight-time-rule middle-europe-and-portugal
Configure the time and date
The switch uses the time command to configure both the time of day and the date.
Also, executing time without parameters lists the switch's time of day and date. Note that the CLI uses a 24-hour
clock scheme; that is, hour (hh) values from 1 p.m. to midnight are input as 13 - 24, respectively.
Syntax:
time [hh:mm [:ss]] [mm/dd/ [yy] yy ]
For example, to set the switch to 9:45 p.m. on November 17, 2012:
HP Switch(config)# time 21:45 11/17/12
How to set the time zone and time source on a HP 2920-48G Switch (J9728A):
The time command don't seem to work on a HP 2920-48G Switch (J9728A) with software ver. WB.15.17.0008 installed.
Use Console Manager Mode [Menu | 2. Switch Configuration | 1. System Information] and edit the Time settings
- You also need a time server source [external or internal] on the network
- A Server [WS 2008/2012] on the network need to be configured as the NTP Server.
Configure the server Registry to enable it as a time server.
Edit the Registry key:
Computer\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpServer
Change the Enable field from 0 to 1
- Open the management console (CLI) and select;
Menu | 2. Switch Configuration | 1. System Information and edit the Time settings
- Time Sync Method [TIMEP/SNTP]: SNTP
- Set Time Sync Method: SNTP
- SNTP Mode: Unicast
- Poll Interval (sec): 720
- Time Zone: 60
- Daylight Time Rule: Middle-Europe-and-Portugal
- Server Address: xxx.xxx.xxx.xxx (The server address is your configured time server)
- Server Version: 3
/CWTech