Problem with A7340A switch

[Marcelo_22]

I have a A7340A (16B) switch and I'm trying connect one rp3440 server and one MSL6000 library on it.
The problem is that, both server and library, only login as Loop.
On the library, when I set the FC port on the router as N_Port it doesn't log into switch but if I set as Auto sense it log as Loop.
I updated the Fabric OS to v.3.2.1a version.
I already tryed to set PID Format to 0 and 1 with no results.
Does anybody have any idea on how can I configure the switch to connect the server and library as Fabric?
An error that occurs at switch boot:
FLOGI before switch ready, disabling port

Thanks in advance..

Marcelo

Here are some information about switch.

root> switchshow
switchName: Libra
switchType: 9.2
switchState: Online
switchMode: Native
switchRole: Principal
switchDomain: 1
switchId: fffc01
switchWwn: 10:00:00:60:69:51:82:83
switchBeacon: OFF
Zoning: OFF
port 0: id 1G No_Light
port 1: id 1G No_Light
port 2: id 2G Online L-Port 1 private, 2 phantom
port 3: id 1G No_Sync
port 4: id N2 No_Light
port 5: id N2 Online L-Port 1 private, 2 phantom
port 6: id N2 No_Light
port 7: id 1G No_Light
port 8: -- 1G No_Module
port 9: -- 2G No_Module
port 10: -- 1G No_Module
port 11: -- 1G No_Module
port 12: -- N2 No_Module
port 13: -- 1G No_Module
port 14: id 1G No_Light
port 15: id 1G No_Light
value = 16 = 0x10

root> version
Kernel: 5.4
Fabric OS: v3.2.1a
Made on: Fri May 12 15:20:59 PDT 2006
Flash: Fri May 12 15:21:57 PDT 2006
BootProm: Tue Oct 30 10:24:38 PST 2001

root> portcfgshow
Ports 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
-------------------+--+--+--+--+----+--+--+--+----+--+--+--+----+--+--+--
Speed 1G 1G 2G 1G AN AN AN 1G 1G 2G 1G 1G AN 1G 1G 1G
Trunk Port ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
Locked L_Port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Locked G_Port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Disabled E_Port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Persistent Disable .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
ISL R_RDY Mode .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
where AN:AutoNegotiate, ..:OFF, ??:INVALID.
value = 0


fabric.ops.BBCredit: 16
fabric.ops.E_D_TOV: 2000
fabric.ops.R_A_TOV: 10000
fabric.ops.dataFieldSize: 2112
fabric.ops.max_hops: 7
fabric.ops.mode.SeqSwitching: 0

Type to continue, Q to stop:
fabric.ops.mode.fcpProbeDisable: 0
fabric.ops.mode.isolate: 0
fabric.ops.mode.longDistance: 0
fabric.ops.mode.noClassF: 0
fabric.ops.mode.pidFormat: 2
fabric.ops.mode.sync: 0
fabric.ops.mode.unicastOnly: 0
fabric.ops.mode.useCsCtl: 0
fabric.ops.mode.vcEncode: 0
fabric.ops.vc.class.2: 2
fabric.ops.vc.class.3: 3
fabric.ops.vc.config: 0xc0
fabric.ops.vc.linkCtrl: 0
fabric.ops.vc.multicast: 7
fabric.ops.wan_rtt_dly_max: 200
fabric.ops.wan_tov: 0

[Mark Poeschl_2 · Accepted solution]

Is "Use Hard AL_PA" disabled on the router in your library?

What kind of HBA do you have in your server? There's normally some kind of utility supplied with it so that you can configure things in the HBA from the server

[Marcelo_22]

Hello Mark,

I've already found the problem.
The HBA's and Library are OK.
The problem was the switch that is old and was configured as quickloop (all ports) and I coldn't find this information in configuration.
Since I executed qldisable command it is working fine.

Thank you
Marcelo

[Marcelo_22]

Thanks