- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- How to change Embedded SATA Configuration in ML110...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-11-2015 07:00 AM
07-11-2015 07:00 AM
How to change Embedded SATA Configuration in ML110 G7 from CLI (command line interface) or iLO CLI
Hello everybody,
I want to remotely manage the SATA Configuration in a cluster of ML110 G7 servers.
When accessing the RBSU over a VGA there is this option:
Advanced Options -> Embedded SATA Configuration -> Enable SATA AHCI Support / Enable SATA Legacy Support
Advanced Options -> Embedded SATA Configuration -> Drive Write Case -> Enabled
This changes the following:
SATA Option ROM ver 2.00.C01 vs HP AHCI SATA Controller (v0.82)
However how do I change these settings from the CLI ROM-Based Setup Utility or iLO CLI?
#-----------------------------------------------------------------------
rbsu> SHOW CONFIG SCRIPT
SET CONFIG NUMLOCK Power-On State Off
SET CONFIG Embedded Serial Port COM 1; IRQ4; IO: 3F8h-3FFh
SET CONFIG Virtual Serial Port Disabled
SET CONFIG USB Control USB Enabled
SET CONFIG Removable Flash Media Boot Sequence External DriveKeys First
SET CONFIG ASR Status Disabled
SET CONFIG ASR Timeout 10 Minutes
SET CONFIG Thermal Shutdown Enabled
SET CONFIG Wake-On LAN Enabled
SET CONFIG POST F1 Prompt Delayed
SET CONFIG Power Button Enabled
SET CONFIG Automatic Power-On Enabled
SET CONFIG Power-On Delay Random Delay
SET CONFIG BIOS Serial Console Port COM 1; IRQ4; IO: 3F8h-3FFh
SET CONFIG BIOS Serial Console Baud Rate 115200
SET CONFIG EMS Console Disabled
SET CONFIG BIOS Interface Mode Auto
SET CONFIG No-Execute Memory Protection Enabled
SET CONFIG Intel(R) Virtualization Technology Enabled
SET CONFIG Intel(R) Hyperthreading Options Enabled
SET CONFIG Processor Core Disable All Cores Enabled
SET CONFIG Intel(R) Turbo Boost Technology Enabled
SET CONFIG Intel(R) VT-d Enabled
SET CONFIG NIC 1 Boot Options Disabled
SET CONFIG NIC 2 Boot Options Disabled
SET CONFIG Option ROM Loading Sequence Load Embedded Devices First
SET CONFIG MPS Table Mode Full Table APIC
SET CONFIG ROM Selection Use Current ROM
SET CONFIG NMI Debug Button Enabled
SET CONFIG Virtual Install Disk Disabled
SET CONFIG PCI Bus Padding Options Enabled
SET CONFIG Power-On Logo Disabled
SET CONFIG Force PCI Hole Base to 1GB Boundary Alignment Disable
SET CONFIG HW Prefetcher Enabled
SET CONFIG Adjacent Sector Prefetch Enabled
SET CONFIG Memory Speed with 2 DIMMs per Channel 1333 MHz Maximum
SET CONFIG Video Options Optional Video Primary, Embedded Video Disabled
SET CONFIG Thermal Configuration Optimal Cooling
SET CONFIG Asset Tag Protection Unlocked
SET CONFIG HP Power Profile Custom
SET CONFIG HP Power Regulator OS Control Mode
SET CONFIG Minimum Processor Idle Power State No C-states
SET CONFIG Maximum Memory Bus Frequency Auto
SET CONFIG PCI Express Generation 2.0 Support Force PCI-E Generation 2
SET CONFIG Dynamic Power Savings Mode Response Fast
SET CONFIG Collaborative Power Control Disabled
SET IPL C: 2
SET IPL A: 4
SET IPL CD 3
SET IPL USB 1
SET BOOT 01 0D333C10 00 00 1F 02
#-----------------------------------------------------------------------
</>hpiLO-> set /map1/accounts1/Administrator password=xxxxx
</>hpiLO-> show /system1/drives1
status=0
status_tag=COMMAND COMPLETED
Sat Jul 11 14:56:38 2015
/system1/drives1
Targets
Properties
Verbs
cd version exit show set
#-----------------------------------------------------------------------