ProLiant Servers (ML,DL,SL)
cancel
Showing results for 
Search instead for 
Did you mean: 

HP ML350 G6 PROBLEM LED CR7

 
Highlighted
Collector

HP ML350 G6 PROBLEM LED CR7

Hello, can someone help me?

I have a ml350 g6 4gb (2x2gb) 1xE5620
The server start, but without video, the cooler is at maximum, I'm sharing a link with video and photo.

A photo where this is the connected cr7 led is the connected server

The video in which the leds are flashing, except cr7, is when the server is down

https://photos.app.goo.gl/qw3w3u3SAe9AJK6q8

5 REPLIES 5
Highlighted
HPE Pro

Re: HP ML350 G6 PROBLEM LED CR7

Hi,

  • Try to reseat the DIMM's, or swap with any working machine.
  • Check by clearing NVRAM:

Follow the steps to clear the NVRAM :

Turn the server off and unplug it. Take the case off.
Locate the System Maintenance switch on the system board.
Turn the switch # 6 on the switch (System Maintenance Switch) to ON position
Cycle the server power up and down.
Reset the switch to the off position.
Restore power and reconfigure the system

 

Regards,

Sudhir

 

I work for HPE
Accept or Kudo

Highlighted
HPE Pro

Re: HP ML350 G6 PROBLEM LED CR7

Hello,

I would request you follow the below steps to fix this issue.

1. Power drain the server. ( Power off the server remove both the power cable and hold on power on switch for 30 Sec.)

Follow the below steps if the issue still persists.

  1. Power of the server and remove the power cable.
  2. Locate the System Maintenance switch on the system board or follow the below link for Maintenance switch.

HP ProLiant ML350 G6 Server - Configuring System Board

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c01726862

a). Turn switch # 6 on the switch (System Maintenance Switch) to ON position

b). Power ON the server and Power OFF again.

c). Reset the switch to the off position.

             d).  If the issue still persists check the server with the minimum configuration. Follow the page no 105 from the below link for minimum configuration.

HP ProLiant ML350 G6 Server User Guide

Breaking the server down to the minimum hardware configuration

https://images10.newegg.com/User-Manual/User_Manual_59-107-066.pdf

  1. Follow the below links, if the issue still persists after performing the above activity. I hope it will help you to isolate and fix the issue.

HP ProLiant ML350 G6 Server - LED Indicators

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c01726637

HP ProLiant Servers - Memory (DIMM) Module in Unsupported Configuration Has Failed: POST Error 201/203/207/209

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c03137775

NOTE: Remove all none-HPE hardware and all add-on PCIe card while performing the above activity.

If you feel this was helpful please click the KUDOS! thumb below!   

Regards,


I am a HPE Employee

Accept or Kudo

Highlighted
Collector

Re: HP ML350 G6 PROBLEM LED CR7

Hi friend
I just performed this procedure.
Still unsuccessful, try only position 6 ON, such as 1, 5 and 6 in and to no avail

Highlighted
Collector

Re: HP ML350 G6 PROBLEM LED CR7

Hi friend
Complete the execution of this procedure.
Still unsuccessful and without access to ILO 2
Add a new video to the link showing a machine

Highlighted
HPE Pro

Re: HP ML350 G6 PROBLEM LED CR7

Hello,

Please share the LED indication, if you followed the below procedure.

1. Power drain the server. ( Power off the server remove both the power cable and hold on power on switch for 30 Sec.)

Follow the below steps if the issue still persists.

  1. Power of the server and remove the power cable.
  2. Locate the System Maintenance switch on the system board or follow the below link for Maintenance switch.

HP ProLiant ML350 G6 Server - Configuring System Board

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c01726862

a). Turn switch # 6 on the switch (System Maintenance Switch) to ON position

b). Power ON the server and Power OFF again.

c). Reset the switch to the off position.

             d).  If the issue still persists check the server with the minimum configuration. Follow the page no 105 from the below link for minimum configuration.

HP ProLiant ML350 G6 Server User Guide

Breaking the server down to the minimum hardware configuration

https://images10.newegg.com/User-Manual/User_Manual_59-107-066.pdf

  1. Follow the below links, if the issue still persists after performing the above activity. I hope it will help you to isolate and fix the issue.

HP ProLiant ML350 G6 Server - LED Indicators

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c01726637

HP ProLiant Servers - Memory (DIMM) Module in Unsupported Configuration Has Failed: POST Error 201/203/207/209

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c03137775

NOTE: Remove all none-HPE hardware and all add-on PCIe card while performing the above activity.

If you feel this was helpful please click the KUDOS! thumb below!   

Regards,


I am a HPE Employee

Accept or Kudo