- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- HPDL380G6 both raid 1 HDD amber light
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-24-2017 08:42 PM
07-24-2017 08:42 PM
Hi,
Any one can guide what should i do if both of my HDD under the RAID1 now in amber light.
Can the data still be recover by replacing to bay 3 first ?
physicaldrive 1I:1:3
Port: 1I
Box: 1
Bay: 3
Status: Failed
Last Failure Reason: Hardware error
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD7
Serial Number: 3NM2BTHK00009751T78X
Model: HP DG146ABAB4
Current Temperature (C): 47
Maximum Temperature (C): 49
PHY Count: 1
PHY Transfer Rate: 3.0Gbps
physicaldrive 1I:1:4
Port: 1I
Box: 1
Bay: 4
Status: Failed
Last Failure Reason: Write retries failed
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD7
Serial Number: 3NM2E8KC00009801H6BJ
Model: HP DG146ABAB4
Current Temperature (C): 48
Maximum Temperature (C): 51
PHY Count: 1
PHY Transfer Rate: 3.0Gbps
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-25-2017 01:48 AM
07-25-2017 01:48 AM
SolutionHmm,
Tough situation.
I do not think it will help. I believe at the moment both of the drives showing errors and they are not accessible.
If I would be in that situation, I woud try below.
- Shut down the sever.
- Take HDD out (remember in which slot was which HDD fitted)
- Turn on the server.
- Once all POST will finish shut down the server.
- Turn off the server
- Put one HDD and turn on the server
- check if you will be able to access the data
- if not turn off the server, take out the HDD and put other one
- turn on the server and put another drive
- check if you can access the data.
If from any of the drives you will be able to access the data than put in second slot fresh HDD in order to replicate the data.
If there will be still no results I would try to upgrade the firmware on the smart array and HDDs. Maybe after firmware upgrade it will resolve some errors.
Let me know about the progress,
Piotr
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-28-2017 02:38 AM
07-28-2017 02:38 AM
Re: HPDL380G6 both raid 1 HDD amber light
By following your steps, i manage to recover the data after powering up with only bay 4.
After that reenabled the vg and it is fine.
Thank you for your advise.