- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Maximum Ventilation Hp Proliant ML350p Gen8 / ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2018 07:16 AM
тАО07-04-2018 07:16 AM
Good Morning,
Our server, at times, appears to have a very loud noise, apparently when there is a power failure (the server is connected to a no-break). So I have to access it via iLO and turn it off, after a few minutes, I turn on the server and the noise disappears. There is no fault on the HDDs (2xHDDs - RAID 1), the LEDs are green, normal. Is there any procedure, or firmware update BIOS (1.13 Nov 08 2012), driver, etc, which can solve this occasional incident?
Waiting feedback. Thank you!
Solved! Go to Solution.
- Tags:
- fan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2018 12:32 PM
тАО07-05-2018 12:32 PM
Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error
Hello
Please, update the BIOS
power managemnte is recommended
And firmware of ILO 4. The ILO 4 managemente the sensors. of the server
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2018 01:06 PM
тАО07-05-2018 01:06 PM
Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error
Good afternoon,
Firstly thanks Fabricio for the feedback.
I downloaded the respective files for the above links, but unfortunately all reported the following error messages:
"The software will not be installed on this system because the required hardware is not present in the system or the firmware does not apply to this system.
iLO Channel Interface driver is not loaded.
Press 'Close' to exit Setup. "
"The software is not supported for installation on this system.
You must install the iLO Channel Interface driver to use this component.
Press 'Close' to exit Setup. "
"The software will not be installed on this system because the required hardware is not present in the system or the firmware does not apply to this system.
iLO Channel Interface driver is not loaded.
Press 'Close' to exit Setup. "
I await your analysis and feeback.
Thank you!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2018 01:19 PM
тАО07-05-2018 01:19 PM
Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error
Install this driver first
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2018 01:23 PM
тАО07-05-2018 01:23 PM
Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error
Thanks, but unfortunately the error below persists in installing this driver.
"The software is not supported for installation on this system.
The iLO Channel Interface Driver must be installed before installing this component.
Press 'Close' to exit Setup. "
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2018 10:18 PM
тАО07-05-2018 10:18 PM
Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error
You need to install the iLO CHIF driver. Follwoing allong with the OS version of the other drivers listed in this thread you need this
Or better yet, download the latest Gen8 SPP and it will contain all the latest Proliant drivers for your system
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2018 05:56 PM
тАО07-09-2018 05:56 PM
SolutionGood evening,
Sorry for the absence, because I was analyzing a new project.
Regarding the last information of the update, it was successful. The forerunners that I informed that occurred error, this time only this:
power managemnte is recommended
who reported mistake.
These regulations solve the problem in relation to the Maximum Ventilation ?
Thank you!