- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ML110 Gen10 s100i SW RAID Support Not Working
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-14-2017 06:39 AM - edited 12-14-2017 07:37 AM
12-14-2017 06:39 AM - edited 12-14-2017 07:37 AM
ML110 Gen10 s100i SW RAID Support Not Working
If Configure s100i integrated controller for SW RAID Support (via system settings), then Storage Administrator detects NO controller and NO hard drive. If change system setting for s100i to AHCI SATA support, then can install Windows 2012R2 and boot it. If leave setting at SW RAID Support, then restore a functioning sysprepped Windows 2012R2 image, Windows will try to boot and then ask for original install media to run Repair - but eventually fails because 'drive is locked'. HP Support unable to help so far - just emails the instructions from the manual on using SW RAID Support - haven't convinced them yet that when using this setting the SSA sees no smart array controller. Anyone have any success with ML110 Gen10, UEFI, s100i set to SW RAID Support and LFF SATA drives?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-13-2018 01:42 PM
02-13-2018 01:42 PM
Re: ML110 Gen10 s100i SW RAID Support Not Working
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2018 03:03 PM
03-14-2018 03:03 PM
Re: ML110 Gen10 s100i SW RAID Support Not Working
I have the same issue. I'm using one LFF HP hard drive. Even when I choose SATA AHCI in RBSU, SSA sees no smart array controller !
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-18-2018 07:45 AM
04-18-2018 07:45 AM
Re: ML110 Gen10 s100i SW RAID Support Not Working
same thing here, it wont load drivers in Windows
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-18-2018 11:28 AM
04-18-2018 11:28 AM
Re: ML110 Gen10 s100i SW RAID Support Not Working
i got it to work, i HAD to copy either CP030473 or CP032245 to a USB thumb drive and plug into front bottom right USB port and got drivers to load in windows setup, could not use ILO virtual drive folder for the drivers, they would fail loading
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-30-2021 06:40 AM
09-30-2021 06:40 AM
Re: ML110 Gen10 s100i SW RAID Support Not Working
Hi GregC1
I am new to HPE and despreate to figure out how you did this.