- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: P400i In Lock-up State after installing 512MB ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2018 07:46 AM
05-18-2018 07:46 AM
We have an older DL360 G5 (not currently under warranty). It is at BIOS version P58 and has an internal P400i array controller with a 256MB cache module. We needed to expand the RAID5 array with a 4th drive (currently shows as a spare). From what I researched we needed to switch the 256MB module with a 512MB module (part number 405148-B21, 512MB BBWC). After installing the 512MB module we get a post error stating "1783-Slot 0 Array controller is in a lock-up State due to a hardware configuration failure." As a result the controller is disabled. The firmware on the P400i is version 7.24. I have made sure the cache mdule and cables are seated properly. Reinstalling the 256MB module reenables the controller. Not sure what else needs to be done/attempted.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2018 11:53 AM
05-18-2018 11:53 AM
SolutionThe firwmware is the latest and the 512 cache is compatible, so you could try to reset the controller by doing following:
power down the server, install the 512 module, remove all drives (remember their exact bay position), start the server without hard drives - check if the 1783 error ist still there.
Power down again, install the drives in their initial positions and start.
If issue persists, the new 512 cache module may be defective.
I am an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2018 01:14 PM
05-18-2018 01:14 PM
Re: P400i In Lock-up State after installing 512MB BBWC
Ok. I will try that and see what happens. Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-15-2018 06:28 AM
06-15-2018 06:28 AM
Re: P400i In Lock-up State after installing 512MB BBWC
I tried everything as directed and still got the 1783 error. I was able to use the battery w/ its cable to attach to the 256MB module and got it working. I will return the 512MB since I believe it is defective.