- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: RAID configuration
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-30-2020 06:25 AM
05-30-2020 06:25 AM
RAID configuration
Hello,
I have a proliant hp DL20 Gen10 server. When I want to configure my disks or my raids I receive the following message "No device found"
Can you show me how to configure raids or create logical drives on the hp proliant DL20 Gen10?
My server has two 1 TB sata hard drives each
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-01-2020 03:06 AM
06-01-2020 03:06 AM
Re: RAID configuration
Hello sawserland,
May i know which raid controller is used for raid configuration ? is there any add on controller or embedded HPE Smart Array S100i SR Gen10 SW RAID
Please Note
− HPE Smart Array S100i SR Gen10 SW RAID will operate in UEFI mode only. For legacy support an additional controller will
be needed,
HPE Smart Array S100i SR Gen10 SW RAID is off by default and must be enabled by selecting 784308-B21.
− The S100i is a 14-port SATA controller, but only 12 ports are accessible as 2 are leveraged to support the 2 M.2 options on
the Primary Riser.
− The S100i supports windows only
Does that drive led illuminates / blinks during power on server ? if yes ensure that SAS cable connection is ok and seated properly from disk backplane to controller.
Let us know if above actions helpes to fix the issue,
Cheers
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-02-2020 02:18 AM
06-02-2020 02:18 AM
Re: RAID configuration
Hello sawserland,
Please do let us know if reported issue is fixed now or you need additional help on same,
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-08-2020 02:20 AM - last edited on 06-08-2020 11:06 PM by Parvez_Admin
06-08-2020 02:20 AM - last edited on 06-08-2020 11:06 PM by Parvez_Admin
Re: RAID configuration
Hello @sawserland ,
Please do let us know if you were able to complete the installation.
Regards