- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: battery failure - SA5300 - how to fix
ProLiant Servers - Netservers
1748274
Members
3915
Online
108761
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-25-2006 02:47 AM
05-25-2006 02:47 AM
battery failure - SA5300 - how to fix
I received an error in event viewer stating that the battery on the SA5300 has failed.
How do I go about replaing it?
(The server is a ML570 - probably 1st generation)
How do I go about replaing it?
(The server is a ML570 - probably 1st generation)
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-25-2006 11:47 AM
05-25-2006 11:47 AM
Re: battery failure - SA5300 - how to fix
Battery Replacement
The Smart Array 5300 has two replaceable battery packs
Description Spare Part Number
Battery, 4.8V 120978-001
> Push down on the botton clip of the battery pack, attached near the lower corner of the array accelarator.
> swing the battery pack away from the Array accelerator to about a 30-degree angle.
>Lift the pack upward to unhook the top of the battery pack
Since both packs are likely to be discharged at a similar rate, repeat the procedure for the another battery pack.
After removing the first battery wait for 15 seconds before replacing the next one
Hook the top of the battery pack to the top of the array accelarator with the pack held at a 30-degree angle to the plane of the array accelarator board
The Smart Array 5300 has two replaceable battery packs
Description Spare Part Number
Battery, 4.8V 120978-001
> Push down on the botton clip of the battery pack, attached near the lower corner of the array accelarator.
> swing the battery pack away from the Array accelerator to about a 30-degree angle.
>Lift the pack upward to unhook the top of the battery pack
Since both packs are likely to be discharged at a similar rate, repeat the procedure for the another battery pack.
After removing the first battery wait for 15 seconds before replacing the next one
Hook the top of the battery pack to the top of the array accelarator with the pack held at a 30-degree angle to the plane of the array accelarator board
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP