- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: internel health led shows red
ProLiant Servers - Netservers
1753867
Members
7380
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-27-2006 07:49 AM
тАО04-27-2006 07:49 AM
internel health led shows red
my server ml370 g2 internel health led on the front panel shows red whenever i power on the server,this causes the server not to boot.after removing the power cord and leaving it for 30 to 45 mins then powering it on it wil then boot. pls how can i solve this problem and the cause of it.
thanks for your help.
thanks for your help.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2006 09:55 PM
тАО04-28-2006 09:55 PM
Re: internel health led shows red
Hi Solomon:
How many power supplys are installed on the server
- is this the hotplug power supply
- If So:
Please remove both power supplys and check the revision # on them
they should be over REV: 06
- If They are below that then they need to be replaced.
Best regards,
Tarek.
How many power supplys are installed on the server
- is this the hotplug power supply
- If So:
Please remove both power supplys and check the revision # on them
they should be over REV: 06
- If They are below that then they need to be replaced.
Best regards,
Tarek.
Hey, look a light at the end of the tunnel.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2006 09:56 PM
тАО04-28-2006 09:56 PM
Re: internel health led shows red
Sorry REV: 06 is Good; 06 is included. but not below that.
Hey, look a light at the end of the tunnel.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP