- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: Problems activating iLO on DL360 G2 server
ProLiant Servers - Netservers
1752815
Members
6253
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-09-2007 06:28 AM
тАО11-09-2007 06:28 AM
Problems activating iLO on DL360 G2 server
I have a new DL360 G2 server with now OS. I have configured all parameters as I normally do for the iLO by pressing F8 when the server boots up. However, after saving these changes and rebooting the server, the message "Intergrated Lights-Out is disabled" still appears on the screens during the boot process. How do you "enable" iLO on this server? Thanks!
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-10-2007 07:25 AM
тАО11-10-2007 07:25 AM
Re: Problems activating iLO on DL360 G2 server
Hello,
ON the system board, you will see SW1, a set of 6/8 system maintenance Switches.
S1 switch is for iLO security override switch.
By default, its set to OFF, which means the iLO Security is ON.
Turn the SWITCH to ON-> security DISABLED.
F8 & configure iLO !
reboot. then switch the S1 back to default OFF position->enable security.
Regards.
ON the system board, you will see SW1, a set of 6/8 system maintenance Switches.
S1 switch is for iLO security override switch.
By default, its set to OFF, which means the iLO Security is ON.
Turn the SWITCH to ON-> security DISABLED.
F8 & configure iLO !
reboot. then switch the S1 back to default OFF position->enable security.
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-28-2007 03:04 PM
тАО12-28-2007 03:04 PM
Re: Problems activating iLO on DL360 G2 server
Okay, thanks, I disabled security and am ready to configure iLo. But when I press F8 I get Array configuration. So how do I get to iLo config?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-28-2007 03:26 PM
тАО12-28-2007 03:26 PM
Re: Problems activating iLO on DL360 G2 server
Ah, I was waiting too long. Press F8 while it iLo message on screen. Got it.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP