- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: ILO 4 and 5 NTP settings
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2019 06:53 AM
тАО12-06-2019 06:53 AM
ILO 4 and 5 NTP settings
Hello,
I have 2 questions:
- How can I check what's the status of ILO NTP synchronisation? Something like ntpq -p in Linux?
- There are NTP settings (not statuses) in ILO GUI under: iLO Dedicated Network Port->SNTP, is the same info available in ILO CLI eg. show /path_to_some_target?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-08-2019 10:48 PM
тАО12-08-2019 10:48 PM
Re: ILO 4 and 5 NTP settings
Hello ,
Please follow the below advisory for iLO commands
Simplivity Hyper-V - NTP Related Issues & Troubleshooting (Page no 4)
Regards,
I am a HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-10-2019 05:06 AM
тАО12-10-2019 05:06 AM
Re: ILO 4 and 5 NTP settings
Hi,
This document doesn't mention any ILO commands.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-10-2019 02:48 PM
тАО12-10-2019 02:48 PM
Re: ILO 4 and 5 NTP settings
Hello,
Please follow the below iLO 4 Command Line Guide
HPE iLO 4 Scripting and Command Line Guide
Regards,
I am a HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2019 01:29 AM
тАО12-11-2019 01:29 AM
Re: ILO 4 and 5 NTP settings
Again. This document is not relevant. It doesn't tell how to check NTP synchronization status from ILO.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2019 06:16 AM
тАО12-11-2019 06:16 AM
Re: ILO 4 and 5 NTP settings
@Stefan_Matela wrote:Hello,
I have 2 questions:
- How can I check what's the status of ILO NTP synchronisation? Something like ntpq -p in Linux?
- There are NTP settings (not statuses) in ILO GUI under: iLO Dedicated Network Port->SNTP, is the same info available in ILO CLI eg. show /path_to_some_target?
THere is not a way to check sync status in the iLO itself.
I cannot find any mention of these setting in the SMASH CLI commands. NTP settings can be shown, set, or changed using RIBCL.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-28-2020 01:00 PM
тАО01-28-2020 01:00 PM
Re: ILO 4 and 5 NTP settings
For everyone's edification, an example on how to set NTP via HPEiLOCmdlets, is:
$SntpServers = ,@("ntp1.domain.com,"ntp2.domain.com")
Set-HPEiLOSNTPSetting -Connection $connection `
-DHCPv4NTPServer Disabled `
-DHCPv6NTPServer Disabled `
-PropagateTimetoHost Disabled `
-Timezone "Atlantic/Reykjavik" `
-SNTPServer $SntpServers
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2022 02:23 AM
тАО06-03-2022 02:23 AM
Re: ILO 4 and 5 NTP settings
Is there really no way to check NTP status on ILO? Are you supposed to just fill in an an adress and hope for the best? No way to know if the NTP server is availible, firewall correctly setup etc? There must be someything I am missing here., are you supposed to work on a different way with this?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2022 11:11 AM
тАО06-03-2022 11:11 AM
Re: ILO 4 and 5 NTP settings
Hope for the best? No, you should know what NTP servers are valid, internal or external. There is a large community that supports pool.ntp.org.
I haven't worked on HPE servers in a couple of years, but maybe they made changes or improvements in iLO 5 to test NTP connectivity.
Good luck to you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2022 11:57 AM
тАО06-03-2022 11:57 AM
Re: ILO 4 and 5 NTP settings
We still only have ILO 4.
But if no one knows about this then I guess there really is no way for the ILO itself to tell you it is in sync.