- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Systems Insight Manager
- >
- Re: [SIM 6.0 WBEM] WBEM protocol not detected
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-27-2010 11:36 PM
тАО05-27-2010 11:36 PM
Management Protocols HTTP:, SNMP:1.0, SMH:2.0
WBEM Provider was installed on server using the latest SmartStart.
Using Configure and Repair Agents tool WBEM configuration fails as follows:
Configure WBEM / WMI user (START) ...
Configure WBEM / WMI user ...... ................................... [SUCCESS]
Set WBEM / WMI user credentials to System protocol settings ........ [SUCCESS]
Re-identifying system to get updated information (START) ...
Re-identification of system .................................... [SUCCESS]
WBEM protocol settings are not valid/enabled for this system in HP SIM. Check yo
ur HP SIM settings for identification via WBEM.
Subscribe to WBEM / WMI Indications ................................. [FAILED]
Thank you all for help!
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2010 07:58 PM
тАО05-28-2010 07:58 PM
Re: [SIM 6.0 WBEM] WBEM protocol not detected
From the Server page on HPSIM, from the Tools tab you should be able to see the credentials it has tried to use.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-01-2010 10:34 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2010 04:40 AM
тАО06-03-2010 04:40 AM
Re: [SIM 6.0 WBEM] WBEM protocol not detected
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-26-2010 12:00 AM
тАО08-26-2010 12:00 AM
Re: [SIM 6.0 WBEM] WBEM protocol not detected
how can you changed the wmi mapper ip address?