- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: DAT 72x6 Eject Magazine Problem
StoreEver Tape Storage
1748154
Members
3592
Online
108758
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2008 06:30 AM
тАО03-20-2008 06:30 AM
DAT 72x6 Eject Magazine Problem
I have a External SCSI DAT 72x6 Autoloader that the magazine will not eject. The error number is 19.
I tried doing a Forced Eject (Hold Eject button for 5 seconds) and the magazine still does not eject. With a forced eject it shows an error number 9.
Can't find anything in Troubleshooting as to what to try next. Any suggestions would be appreciated.
Thanks,
I tried doing a Forced Eject (Hold Eject button for 5 seconds) and the magazine still does not eject. With a forced eject it shows an error number 9.
Can't find anything in Troubleshooting as to what to try next. Any suggestions would be appreciated.
Thanks,
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2008 04:28 AM
тАО03-24-2008 04:28 AM
Re: DAT 72x6 Eject Magazine Problem
I was able to get the magazine to eject. Now when I try to load the new magazine it goes through the Mag Check, but no tapes show on the display and at the end I'm getting an error 42.
Thanks
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-07-2008 11:29 PM
тАО05-07-2008 11:29 PM
Re: DAT 72x6 Eject Magazine Problem
As you dragged magazine ?
Roughly the same situation, only mistake 58.
Roughly the same situation, only mistake 58.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP