StoreEver Tape Storage
1748252 Members
3979 Online
108760 Solutions
New Discussion юеВ

Re: HP StorageWorks e1200-320 could not save data

 
SOLVED
Go to solution
Michael Boschke
Occasional Advisor

HP StorageWorks e1200-320 could not save data

Hello,

I would like to connect my MSL6030 via FC direct to an HBA. In that way, I have to configure the FC-Port to Autosensing.

If I configure that on the web-interface, the setting return to the factory default after reboot. If I configure that via Telnet, then I can just read the error message "Could not save data".

Why that Interface-card not save the settings? What do I wrong? Has anyone any idea what could be the problem?

Regards

Micha

11 REPLIES 11
Torsten.
Acclaimed Contributor

Re: HP StorageWorks e1200-320 could not save data

I would try a reset to defaults first:

 

1) Baud Rate Configuration

2) Ethernet and SNMP Configuration

3) Fibre Channel Configuration

4) Parallel SCSI Configuration

5) Device Mapping

6) Trace and Event Settings Configuration

7) Real-Time Clock Configuration

8) Active Fabric Configuration



A) Save Configuration

B) Restore Last Saved Configuration

C) Reset to Factory Defaults


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Michael Boschke
Occasional Advisor

Re: HP StorageWorks e1200-320 could not save data

Sorry, but Reset to Factory Defaults didn't solve the problem.

After the Reset and Reboot I get the error message again, if i type A - Save Configuration.

Torsten.
Acclaimed Contributor

Re: HP StorageWorks e1200-320 could not save data

The board is maybe bad?

How about firmware?

Latest version I have is 5.9.63.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Michael Boschke
Occasional Advisor

Re: HP StorageWorks e1200-320 could not save data

Firmware 5.9.63 is installed. If I try to connect the card via ftp, I don't get a directory listing.

Befehl:    LIST
Antwort:    150 Opening BINARY mode data connection
Antwort:    550 No files found or invalid directory or permission problem
Fehler:    Verzeichnisinhalt konnte nicht empfangen werden

Can I "format/recover" the flash or is the flash corrupted?

 

Torsten.
Acclaimed Contributor

Re: HP StorageWorks e1200-320 could not save data

not sure if list works at all.

try

get myconfig.cfg

does it work?

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Michael Boschke
Occasional Advisor

Re: HP StorageWorks e1200-320 could not save data

No, unfortunately not    :-(

331 Password required
Kennwort:
230 User logged in
ftp> get myconfig.cfg
200 Port set okay
550 File "myconfig.cfg" not found or permission problem
ftp> dir
200 Port set okay
150 Opening ASCII mode data connection
  size          date       time       name
--------       ------     ------    --------
       0    Jan-18-2018  00:19:46   5.9.63_fw_winston.dlx
    1024    Jan-18-2018  00:19:46   curtrace.txt

550 No files found or invalid directory or permission problem
FTP: 204 Bytes empfangen in 0,00Sekunden 204000,00KB/s
ftp>

ftp> ls
200 Port set okay
150 Opening ASCII mode data connection
5.9.63_fw_winston.dlx
curtrace.txt
prvtrace.txt
*.cfg
*.o
*.bin

226 Transfer complete
FTP: 65 Bytes empfangen in 0,00Sekunden 65000,00KB/s
ftp>

However, I was able to download the file curtrace.txt but not the file prvtrace.txt. Would it make sense to reinstall the firmware?

Torsten.
Acclaimed Contributor

Re: HP StorageWorks e1200-320 could not save data

Did you use "root" as the user?

 


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Michael Boschke
Occasional Advisor

Re: HP StorageWorks e1200-320 could not save data

Yes, I login with root.

tapelibraryfixr
Trusted Contributor
Solution

Re: HP StorageWorks e1200-320 could not save data

im not sure why it would say "cant save data" but when i have configured these in the past i have had to unplug the fiber cable, then save the config, reboot the card and then plug in the fiber cable. for some reason the config doesnt save when the cable is plugged in.