- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- StoreVirtual Storage
- >
- Re: P4000 application managed snashot SAN I/Q 9.5
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-30-2011 12:00 PM
10-30-2011 12:00 PM
P4000 application managed snashot SAN I/Q 9.5
Hi,
I red several documents about implementing application aware snapshots with vcenter 5.
Now i red the following documents:
1. ApplicationAwareSnapshotManagerDeploymentGuide
2. HP SAN User guide
As stated in the documentation (it's kinda unclear) the following needs to be applied.
In my case the CMC server is also VC so no routing issues.
1. Configured ISCSI on CMC/VC server. I added the VMFS to READ for the VC. (don't want to destroy my VMFS volumes)
I added a second NIC for ISCSI. I can ping the the VC on both LAN and ISCSI network. So no routing issues.
2. Added the VC to serverlist in CMC and put the connection ip server (LAN ip and ISCSI tried)of the VC.
3. Installed the HP application manager (Default port)
4. Configured authentication (succesfull test)
when i try a app integrated snapshot i immediatly get : failed to create snapshot. Point in time works fine.
Now what i tried:
1. changed port
2. Add the ip address with port in the CMC so 10.10.10.10:5989
3. Checked if my windows 2008 r2 "sees" the LUNS in the storage management.
I red all the documenation but it's kinda unclear what i'm missing here.
anyone got a idea?
1.
Still error.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-30-2011 03:07 PM
10-30-2011 03:07 PM
Re: P4000 application managed snashot SAN I/Q 9.5
Can you verify that you have dont the following?
On Windows Host/Application server, install Application Aware Snapshot Manager
Connect to Vi Center server on a host server, using Vi Client and add a new data store.
It is recommended that VMware tools is installed on the ESX server as it aids the Application Aware Snapshot process.
Ensure that you edit any virtual machines that will use Application Aware Snapshot to be Point-In-Time.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-31-2011 03:50 AM
10-31-2011 03:50 AM
Re: P4000 application managed snashot SAN I/Q 9.5
Hi Emilo,
If you red my post you see that i have done alll that. Installing VMware tools on ESX isn't possible. Are you sure you meant that? you cannot install VMware tools on ESX.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-28-2011 04:27 AM
12-28-2011 04:27 AM
Re: P4000 application managed snashot SAN I/Q 9.5
I've did the same installation but I get this error when I try to create a VSS snapshot from CMC.
" A general error occurred that is not covered by a more specfic error code: Application server configuration service at 128.1.0.100 not found: (401 Unautherized)"
128.1.0.100 is my iSCSI IP from my ESX host??
I can ping from VC to the CMC server. (VC and CMC are both on LAN and iSCSI)
I added VC server to the CMC server list.
VC can see the "testlun".
Authentication Console on the VC give succesfull result.
What am I missing here?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-21-2012 01:36 AM
02-21-2012 01:36 AM
Re: P4000 application managed snashot SAN I/Q 9.5
Well yes, I do have the same issue like Aart.
Same behavoir.
anything new on this thread?
thx, Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-10-2012 01:39 PM
07-10-2012 01:39 PM
Re: P4000 application managed snashot SAN I/Q 9.5
Do you have any uppercase letters in CMC volumes?
It seems that with all lowercase it works.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-10-2012 02:43 PM
07-10-2012 02:43 PM
Re: P4000 application managed snashot SAN I/Q 9.5
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-11-2012 04:33 AM
08-11-2012 04:33 AM
Re: P4000 application managed snashot SAN I/Q 9.5
dear,
we faced many similar issues and was solved by installing an updated version of the HP P4000 Application Aware Snapshot Manager. the updated version fixed the following bug according to our case (may be it fix other problems as well) :
if you have an NFS based data store in the VMWARE , the CMC will fail to scan that nfs volume while trying to establish the application awhich prevents the application
pls. insure you have the latest SW in both lefthand and server sides
good luck