- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: DEFAULT_VLAN switch HP
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2010 02:17 AM
тАО01-14-2010 02:17 AM
DEFAULT_VLAN switch HP
voila j'ai un r├йseau local constitu├й de plusieurs switchs HP en mode ├йtoile connect├й tous a un switch disant federateur,
sur les quelles on a configurer plusieurs Vlans, les vlans communiques entre eux, --> (on a tagg├й les ports qui relient les switchs entre eux avec ces vlans )
je voudrais savoir si je dois tagg├й aussi ces ports (qui relient les switchs entre eux ) avec le vlan par default (vlan 1) , sachant que je ne l'utilise pas, et je ne sais pas si la communication entre switch (protocole inter switch) se fait uniquement via le vlan 1 donc il faut obligatoirement le tagg├й sur ces ports pour assur├й le bon fonctionnement du r├йseau ?
Merci pour votre retour :)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2010 03:05 AM
тАО01-14-2010 03:05 AM
Re: DEFAULT_VLAN switch HP
nous voudrais parler en anglais ;-) Could you post your question in english please.
Cheers,
Michael
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2010 10:17 AM
тАО01-14-2010 10:17 AM
Re: DEFAULT_VLAN switch HP
voila I have a LAN consisting of several switches HP mode
Star all connected to a switch saying unifying
on which we configure multiple VLANs, VLANs communicated
between them, -> (we have tagged him the ports that connect the switches between them
with these VLANs)
I would like to know if I tagged him as the ports (which connect
switches between them) with the default VLAN (VLAN 1), knowing that I
use it, and I do not know if the communication between switch
(inter-switch protocol) is only via the vlan 1 then it must
Tagger mandatory on these ports for the good functioning
network?
Thank you for your return:)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2010 11:18 AM
тАО01-14-2010 11:18 AM
Re: DEFAULT_VLAN switch HP
I assume that the following thread will answer your questions
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1398254
Moreover Management protocols (LLDP, STP, LACP, ...) are sent in VLAN 1 - independantly if you tag it or not. Bascially you can leave VLAN 1 in the default state (untagged) and just tag your additional VLANs.
Cheers,
Michael
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2010 11:21 PM
тАО01-14-2010 11:21 PM
Re: DEFAULT_VLAN switch HP
actually, one little detail of your post is incorrect.
With Cisco it is correct, that (at least several) management protocols will be sent over the native vlan and/or vlan 1. So, there it is good best practice to leave vlan 1 as the native one.
With ProCurve, however, all management traffic will simply be sent untagged only; independant of the port's vlan configuration!
Saying: management traffic is not bound to a particular vlan at all.
Regards,
Ralf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2010 01:16 AM
тАО01-15-2010 01:16 AM
Re: DEFAULT_VLAN switch HP
Thank you for your explanation, so I leave my setup as it is now
just another question:) for vlan 1 is what it is that the ports of switches are no untagged: exple Switche HP 50 ports:
vlan 1
name "DEFAULT_VLAN"
no ip address
no untagged 1-50
Thank you for your return.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2010 01:23 AM
тАО01-15-2010 01:23 AM
Re: DEFAULT_VLAN switch HP
A port can be untagged member of one single vlan at a time only.
--> So, if a port is configured to be untagged member of - let's say - vlan 10, it will be automatically marked no untagged for vlan 1.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-15-2010 02:33 AM
тАО01-15-2010 02:33 AM
Re: DEFAULT_VLAN switch HP
so if you want a port to belong to a specific vlan then untag it on that vlan
Regards