- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: HP Procurve 1700 -24 VLAN Setup
Switches, Hubs, and Modems
1753733
Members
4668
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2011 04:39 PM
01-20-2011 04:39 PM
HP Procurve 1700 -24 VLAN Setup
Hi,
I have an HP Procurve 1700. I am trying to setup VLANs on my switch so that servers cannot see each other. All servers have static IPs. I am performing the following steps:
Uplink and All ports are VLAN ID 1
I remove a port from VLAN 1 and add it to VLAN 2 as well as the uplink.
After this I cannot ping the server on the other side of the VLAN 2 port.
This seems like it should be straight forward.
Any suggestions or am I completely missing something?
Thank You
Brent
I have an HP Procurve 1700. I am trying to setup VLANs on my switch so that servers cannot see each other. All servers have static IPs. I am performing the following steps:
Uplink and All ports are VLAN ID 1
I remove a port from VLAN 1 and add it to VLAN 2 as well as the uplink.
After this I cannot ping the server on the other side of the VLAN 2 port.
This seems like it should be straight forward.
Any suggestions or am I completely missing something?
Thank You
Brent
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-22-2011 09:58 AM
01-22-2011 09:58 AM
Re: HP Procurve 1700 -24 VLAN Setup
If you want the server on VLAN 2, untag the port that the server is plugged into for VLAN 2. If you need that vlan to go across an uplink, make sure you 'tag' the uplink and leave vlan 1 "untagged". You can only have 1 vlan untagged across a port.
How are you routing these servers? Are you re-ip addressing the servers once you move them to vlan 2 and then assigning an IP address to vlan 2 on a routing switch? Or do you just simply need layer 2 connectivity for the server to another device on the same vlan?
How are you routing these servers? Are you re-ip addressing the servers once you move them to vlan 2 and then assigning an IP address to vlan 2 on a routing switch? Or do you just simply need layer 2 connectivity for the server to another device on the same vlan?
www.traversasolutions.com;http://www.linkedin.com/pub/kyle-massey/22/23/126
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP