Switches, Hubs, and Modems
cancel
Showing results for 
Search instead for 
Did you mean: 

Router on a stick Pfsense Aruba 2930f

 
Highlighted
New Member

Router on a stick Pfsense Aruba 2930f

Good morning, 

First, sorry for my english ;

I would like to configure my pfsense by routing on a stick like a cisco switch like on this tutorial ( https://www.highlnk.com/2014/06/configuring-vlans-on-pfsense/ )

I made a network diagram (see in PJ)

https://zupimages.net/viewer.php?id=20/13/vi5j.png  

and I configured my vlans on pfsense (see PJ 2) all my VLANS pass my LAN port (em0) which is on a physical server.

https://zupimages.net/viewer.php?id=20/13/pdmx.png  

PORT Pfsense VLAN 1: 192.168.1.1
PORT Pfsense VLAN 10 : 192.168.10.1
PORT Pfsense VLAN 20 : 192.168.20.1
PORT Pfsense VLAN 30 : 192.168.30.1
PORT Pfsense VLAN 40 : 192.168.40.1
PORT Pfsense VLAN 50 : 192.168.50.1
PORT Pfsense VLAN 60 : 192.168.60.1
PORT Pfsense VLAN 80 : 192.168.80.1

(PJ 3 example VLAN port 60)

https://zupimages.net/viewer.php?id=20/13/1x8y.png  

I have also activated the DHCP pool for each VLANS (see example PJ 4 for VLAN 60).

https://zupimages.net/viewer.php?id=20/13/4u4n.png 

But it's on my Aruba 2930f that I have a big doubt (Protoswitch) where I also configured the VLANS with the same ID:
VLAN 1: 192.168.1.254
VLAN 10: 192.168.10.254
VLAN 20: 192,168,20,254
VLAN 30: 192.168.30.254
VLAN 40: 192,168,40,254
VLAN 50: 192,168,50,254
VLAN 60: 192,168,60,254
VLAN 80: 192,168,80,254

Finally I have TAGGED on port 6 all the VLANS which leads to my pfsense but it doesn't work... I don't communicate between my pfsense and my switch whatever the port is, do you have an idea ?

Thanks in advance

--------------------------------------------------

Bonjour,

Je voudrais configurer mon pfsense en router on a stick comme un switch cisco comme sur ce tuto ( https://www.highlnk.com/2014/06/configuring-vlans-on-pfsense/)

J'ai fait un schéma réseau (voir en PJ)

https://zupimages.net/viewer.php?id=20/13/vi5j.png 

et j'ai configuré mes vlans sur pfsense (voir PJ 2) tout mes VLANS passent pas ma patte LAN (em0) qui est sur un serveur physique.

https://zupimages.net/viewer.php?id=20/13/pdmx.png 

PORT Pfsense VLAN 1 : 192.168.1.1
PORT Pfsense VLAN 10 : 192.168.10.1
PORT Pfsense VLAN 20 : 192.168.20.1
PORT Pfsense VLAN 30 : 192.168.30.1
PORT Pfsense VLAN 40 : 192.168.40.1
PORT Pfsense VLAN 50 : 192.168.50.1
PORT Pfsense VLAN 60 : 192.168.60.1
PORT Pfsense VLAN 80 : 192.168.80.1

(PJ 3 exemple port VLAN 60)

https://zupimages.net/viewer.php?id=20/13/1x8y.png 

J'ai également activé le pool DHCP pour chaque VLANS ( voir exemple PJ 4 pour VLAN 60)

https://zupimages.net/viewer.php?id=20/13/4u4n.png 

Mais c'est sur mon Aruba 2930f que j'ai un gros doute (Protoswitch) où j'ai également configurer les VLANS avec les même ID:
VLAN 1 : 192.168.1.254
VLAN 10 : 192.168.10.254
VLAN 20 : 192.168.20.254
VLAN 30 : 192.168.30.254
VLAN 40 : 192.168.40.254
VLAN 50 : 192.168.50.254
VLAN 60 : 192.168.60.254
VLAN 80 : 192.168.80.254

Enfin j'ai TAGGED sur le port 6 tous les VLANS qui mène à mon pfsense mais cela ne fonctionne pas... je ne communique pas entre mon pfsense et mon switch quelque soit le port avez vous une idée ?

Merci d'avance

1 REPLY 1
Highlighted
Honored Contributor

Re: Router on a stick Pfsense Aruba 2930f

Since the IPv4 routing duty is resposability of your pfSense I guess your Aruba 2930F is not doing routing (isn't it? [*])...if so can you post the output of show vlan port x detail CLI Command on your Aruba 2930F (where x is the uplink port on your Aruba 2930F to your Firewall, port that you should already have tagged with required VLANs)?

It's not clear...is the next hop (the Firewall) directly connected to the Aruba 2930F? if so...I guess by using port x on Aruba 2930F and a "LAN" port (with various tagged VLANs) on the Firewall side. Is it correct?

[*] with the IPv4 Routing disabled you should configure a Default Gateway for the traffic generated on the Switch itself (as example, for managing it).