- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Spanning Tree config via menu on an ProCurve 2...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2012 11:56 PM
тАО04-29-2012 11:56 PM
Spanning Tree config via menu on an ProCurve 2610-48 PWR
Hi,
I have a new ProCurve 2610-48 PWR Switch with the latest firmware. Within the menu, there is no option to configure spanning tree. On the commandline I can configure it. Does I need configure something to get the spanning tree point in the menu?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2012 01:11 AM
тАО04-30-2012 01:11 AM
Re: Spanning Tree config via menu on an ProCurve 2610-48 PWR
U can enable stp under "run setup" in main menu. But I didn't found detail configurations. I would configure it via cli.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2012 01:24 AM
тАО04-30-2012 01:24 AM
Re: Spanning Tree config via menu on an ProCurve 2610-48 PWR
on my other ProCurve switches i have an detail setup for stp under "Main Menu -> 2. Switch Configuration -> 4. Spanning Tree Operation".
The Option for enable stp under "run setup" I already tried, even with a restart of the switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2012 02:42 AM
тАО04-30-2012 02:42 AM
Re: Spanning Tree config via menu on an ProCurve 2610-48 PWR
It's been disappearing from the menu for a while:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2012 03:07 AM
тАО04-30-2012 03:07 AM
Re: Spanning Tree config via menu on an ProCurve 2610-48 PWR
Tanks, this explains why I can not activate it.