- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Cold Installing HP-UX 11.23 on an Interity box...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 03:33 AM
тАО11-04-2010 03:33 AM
Cold Installing HP-UX 11.23 on an Interity box with usb dvd
I have attached the usb dvd to the front and rear usb ports to try both, and power cycled the unit.
My console is attached via the serial port and the boot process begins. It enters the EFI boot manager and automatically starts the autoboot install from the dvd. I have also stop the process and tried "fs0:", INSTALL same results.
The system begins
Loading Section 0
Loading Symbol Table
Loading ram disk file IINSTALLFS
Launching IINSTALL
Console is on a serial device
Booting Kernel
Memory Class Setup
Then a 1-2 min pause then bad news
Interruption Type Data TLB Fault
Shutdown State 8 type 0x2
Tries to do a memory dump but not configured for it
It then cycles back to EFI Boot Manager and tries it again. Simply press any key to stop it.
Any assistance would be greatly appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 03:50 AM
тАО11-04-2010 03:50 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
The USB dvd drive must be compatible for hp-ux 11.23.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 03:52 AM
тАО11-04-2010 03:52 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 03:57 AM
тАО11-04-2010 03:57 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 03:59 AM
тАО11-04-2010 03:59 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 04:02 AM
тАО11-04-2010 04:02 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
Check for support matrix on manufacturer's website.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 04:05 AM
тАО11-04-2010 04:05 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
See
http://h20341.www2.hp.com/integrity/w1/en/entry-class/rx2660-options.html
Product# AD142A or AD143A
Meanwhile configure MP/Ilo with an IP address and use the virtual media. It may be slow, but working.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2010 04:31 AM
тАО11-04-2010 04:31 AM
Re: Cold Installing HP-UX 11.23 on an Interity box with usb dvd
Item Number: A180-1219
Model: LZ.23800.015
8X DVD├В┬▒RW Super-Multi Double Layer Optical Drive
Transfer Rates: Write DVD+R: 8X DVD+RW: 8X DVD+R DL: 6X DVD-R : 8X DVD-RW: 6X DVD-R DL: 6X CD-R: 24X CDRW: 24X
Transfer Rates: Write DVD+R: 8X DVD+RW: 8X DVD-R : 8X DVD-RW: 8X CD-R: 24X CD-RW: 24X
Supported Disc: CD-DA, CD-ROM, CD-ROM / XA, mixed mode, Video-CD, Photo CD, Enhanced CD, CD Plus, CD-Text, DVD-Video(8cm/12cm, Single and Dual Layer), DVDROM( 8cm/12cm, Single and Dual Layer), Multi-Border, Multi- Session
Unable to find a support matrix for the product