- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Number simultaneous connection
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2010 12:45 PM
тАО09-18-2010 12:45 PM
Are there sommebody to to give some lights.
The number of connection to a hpux 11iv3 is it limited.
We have a hpux 11iv3 server (rx6600). We have to etablish 200 simultuneous connection ( via telnet). But after 60 connections the over connection failed. I would know if is exist a parameter that i can change to be able to etablish all connection.
Thx in advance for your help.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2010 01:34 PM
тАО09-18-2010 01:34 PM
Re: Number simultaneous connection
http://forums.itrc.hp.com/service/forums/questionanswer.do?threadId=1344064
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2010 05:14 AM
тАО09-20-2010 05:14 AM
Re: Number simultaneous connection
It is a kernel parameter you have to change it using sam:
root@xxxxx:/# kctune | grep -i nstrtel
nstrtel 60 Default
Reards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2010 06:01 AM
тАО09-20-2010 06:01 AM
SolutionThe kernel parameters nstrtel, nstrpty and npty are probably all at 60. Set them all to 500 (for future expansion). Then run insf -e to install the additional device files. Without insf, you'll stop at 60 connections because there are no additional device files available.
The 3 kernel parameters should always be set the same. Although you could go through your system looking for the different connection types and allocate as needed, it is much simpler to set them all the same.
Bill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-21-2010 02:32 AM
тАО09-21-2010 02:32 AM
Re: Number simultaneous connection
You have all right.
Special Thank to Bill Hassell you answer is the most complete and have permit me to resolve my issue.
Thx again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-21-2010 02:34 AM
тАО09-21-2010 02:34 AM